Use of this information is subject to copyright laws and may require the permission of the owner of the information, as described in the ECHA Legal Notice.
EC number: 201-162-7
CAS number: 78-96-6
4.1. Description of first aid measures
Immediately remove contaminated clothing. If danger of loss of consciousness, place patient in recovery position and transport accordingly. Apply artificial respiration if necessary. First aid personnel should pay attention to their own safety.
Immediately administer a corticosteroid from a controlled/metered dose inhaler. Keep patient calm, remove to fresh air, seek medical attention.
On skin contact:
Immediately wash thoroughly with plenty of water, apply sterile dressings, consult a skin specialist.
On contact with eyes:
Immediately wash affected eyes for at least 15 minutes under running water with eyelids held open, consult an eye specialist.
Immediately rinse mouth and then drink 200-300 ml of water, seek medical attention.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms: The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11., Further symptoms are possible
4.3. Indication of any immediate medical attention and special treatment needed
Treatment: Treat according to symptoms (decontamination, vital functions), no known specific antidote.
5.1. Extinguishing media
Suitable extinguishing media:
water spray, dry powder, foam
5.2. Special hazards arising from the substance or mixture
nitrogen oxides, carbon oxides
The substances/groups of substances mentioned can be released in case of fire. Under certain conditions in case of fire other hazardous combustion products may be generated.
5.3. Advice for fire-fighters
Special protective equipment:
Wear self-contained breathing apparatus and chemical-protective clothing.
Dispose of fire debris and contaminated extinguishing water in accordance with official regulations.
6.1. Personal precautions, protective equipment and emergency procedures
Avoid inhalation. Avoid contact with the skin, eyes and clothing.
6.2. Environmental precautions
Do not discharge into drains/surface waters/groundwater.
6.3. Methods and material for containment and cleaning up
For large amounts: Pump off product.
For residues: Pick up with suitable absorbent material (e.g. sand, sawdust, general-purpose binder, kieselguhr).
Clean contaminated floors and objects thoroughly with water and detergents, observing environmental regulations. Collect waste in suitable containers, which can be labeled and sealed. Incinerate or take to a special waste disposal site in accordance with local authority regulations.
6.4. Reference to other sections
Information regarding exposure controls/personal protection and disposal considerations can be found in section 8 and 13.
7.1. Precautions for safe handling
Ensure thorough ventilation of stores and work areas. Handle in accordance with good industrial hygiene and safety practice. When using do not eat, drink or smoke. Hands and/or face should be washed before breaks and at the end of the shift.
Protection against fire and explosion:
Prevent electrostatic charge - sources of ignition should be kept well clear - fire extinguishers should be kept handy.
Temperature class: T2 (Autoignition temperature >300 °C).
7.2. Conditions for safe storage, including any incompatibilities
Segregate from acids and acid forming substances.
Storage class according to TRGS 510 (originally VCI, Germany): (8A) Combustible corrosive substances
Storage temperature: 20 °C
Storage duration: 24 Months
May yellow after lengthy storage.
From the data on storage duration in this safety data sheet no agreed statement regarding the warrantee of application properties can be deduced.
7.3. Specific end use(s)
See exposure scenario(s) in the attachment to this safety data sheet.
8.1. Control parameters
Components with occupational exposure limits
The surveillance of the workplace by exposure measurements may be necessary, in order to proof the efficiency of safety measures, for example ventilation or the need of respiratory protection. Since this requires a specific competency, only accredited laboratories should be contracted. Regarding suitable methods to assess inhalative exposure the European Standards EN 482, 689 and 14042 are to be considered. In addition the TRGS 402 has to be observed in Germany.
Short Term Exposure Classification: (TRGS 900 (DE)), Vapor and aerosol
Category I: Substances for which the localized effect has an assigned exposure limit or for substances with a sensitizing effect in respiratory passages
OEL 5,8 mg/m3 ; 2 ppm (TRGS 900 (DE)), Vapor and aerosol
Ceiling limit value/factor: 2
Sum of vapors and aerosols.
freshwater: 0,0327 mg/l
marine water: 0,00327 mg/l
intermittent release: 0,327 mg/l
sediment (freshwater): 0,177 mg/kg
sediment (marine water): 0,0177 mg/kg
soil: 0,0161 mg/kg
STP: 3,3 mg/l
Long-term exposure- systemic effects, Inhalation: 8,5 mg/m3
Long-term exposure- systemic effects, Inhalation: 2,1 mg/m3
Long-term exposure- systemic effects, oral: 0,67 mg/kg
8.2. Exposure controls
Personal protective equipment
Respiratory protection in case of vapour/aerosol release. Gas filter for gases/vapours of organic compounds (boiling point >65 °C, e. g. EN 14387 Type A)
Chemical resistant protective gloves (EN 374)
Suitable materials also with prolonged, direct contact (Recommended: Protective index 6, corresponding > 480 minutes of permeation time according to EN 374):
chloroprene rubber (CR) - 0.5 mm coating thickness
nitrile rubber (NBR) - 0.4 mm coating thickness
butyl rubber (butyl) - 0.7 mm coating thickness
fluoroelastomer (FKM) - 0.7 mm coating thickness
polyvinylchloride (PVC) - 0.7 mm coating thickness
Manufacturer's directions for use should be observed because of great diversity of types.
Supplementary note: The specifications are based on tests, literature data and information of glove manufacturers or are derived from similar substances by analogy. Due to many conditions (e.g. temperature) it must be considered, that the practical usage of a chemical-protective glove in practice may be much shorter than the permeation time determined through testing.
Tightly fitting safety goggles (cage goggles) (e.g. EN 166) and face shield.
Body protection must be chosen depending on activity and possible exposure, e.g. apron, protecting boots, chemical-protection suit (according to EN 14605 in case of splashes or EN ISO 13982 in case of dust).
General safety and hygiene measures
Avoid contact with the skin, eyes and clothing. Avoid inhalation of vapour. Handle in accordance with good industrial hygiene and safety practice. Wearing of closed work clothing is required additionally to the stated personal protection equipment. When using, do not eat, drink or smoke. Hands and/or face should be washed before breaks and at the end of the shift. Gloves must be inspected regularly and prior to each use. Replace if necessary (e.g. pinhole leaks). Take off immediately all contaminated clothing. Wash contaminated clothing before reuse. Store work clothing separately.
No hazardous reactions if stored and handled as prescribed/indicated.
Corrosion to metals:
No corrosive effect on metal.
Formation of flammable gases: Remarks: Forms no flammable gases in the presence of water.
10.2. Chemical stability
The product is stable if stored and handled as prescribed/indicated.
10.3. Possibility of hazardous reactions
The progress of reaction is exothermic. Reacts with isocyanates. Reacts with oxidizing agents. Reacts with halogenated compounds. Reacts with acid chlorides. Reacts with acids. Incompatible with acid chlorides and acid anhydrides.
10.4. Conditions to avoid
Avoid extreme temperatures. See MSDS section 7 - Handling and storage.
10.5. Incompatible materials
Substances to avoid:
isocyanates, oxidizing agents, acid chlorides, acid anhydrides, acids, acid forming substances
10.6. Hazardous decomposition products
Hazardous decomposition products:
carbon oxides, nitrogen oxides, nitrous gases
13.1. Waste treatment methods
Incinerate in suitable incineration plant, observing local authority regulations.
A waste code in accordance with the European waste catalog (EWC) cannot be specified, due to dependence on the usage.
The waste code in accordance with the European waste catalog (EWC) must be specified in cooperation with disposal agency/manufacturer/authorities.
Contaminated packaging should be emptied as far as possible; then it can be passed on for recycling after being thoroughly cleaned
Information on Registered Substances comes from registration dossiers which have been assigned a registration number. The assignment of a registration number does however not guarantee that the information in the dossier is correct or that the dossier is compliant with Regulation (EC) No 1907/2006 (the REACH Regulation). This information has not been reviewed or verified by the Agency or any other authority. The content is subject to change without prior notice.Reproduction or further distribution of this information may be subject to copyright protection. Use of the information without obtaining the permission from the owner(s) of the respective information might violate the rights of the owner.
За да гарантираме, че се възползвате максимално от функциите на нашия уебсайт, сме въвели „бисквитки“.
Welcome to the ECHA website. This site is not fully supported in Internet Explorer 7 (and earlier versions). Please upgrade your Internet Explorer to a newer version.
Do not show this message again