Registration Dossier

Administrative data

First-aid measures

4.1. Description of first aid measures
Immediately remove contaminated clothing. If the patient is likely to become unconscious, place and transport in stable sideways position (recovery position). First aid personnel should pay attention to their own safety.

If inhaled:
Keep patient calm, remove to fresh air, seek medical attention. Immediately administer a corticosteroid from a controlled/metered dose inhaler.

On skin contact:
Immediately wash thoroughly with plenty of water, apply sterile dressings, consult a skin specialist.

On contact with eyes:
Immediately wash affected eyes for at least 15 minutes under running water with eyelids held open, consult an eye specialist.

On ingestion:
Rinse mouth immediately with water. If swallowed, seek medical advice immediately and show this container or label.


4.2. Most important symptoms and effects, both acute and delayed
Symptoms: The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11.


4.3. Indication of any immediate medical attention and special treatment needed
Treatment: Treat according to symptoms (decontamination, vital functions), no known specific antidote. Pulmonary odema prophylaxis. Medical monitoring for at least 24 hours.

Fire-fighting measures

5.1. Extinguishing media
Suitable extinguishing media:
water spray, dry powder, foam, carbon dioxide

5.2. Special hazards arising from the substance or mixture
carbon monoxide, Carbon dioxide, nitrous gases

5.3. Advice for fire-fighters
Special protective equipment:
Wear self-contained breathing apparatus and chemical-protective clothing.

Further information:
Dispose of fire debris and contaminated extinguishing water in accordance with official regulations.

Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures
Breathing protection required. Avoid contact with the skin, eyes and clothing.

6.2. Environmental precautions
Do not discharge into drains/surface waters/groundwater.

6.3. Methods and material for containment and cleaning up
For small amounts: Pick up with absorbent material (e.g. sand, sawdust, general-purpose binder).
For large amounts: Pump off product.
Cleaning operations should be carried out only while wearing breathing apparatus. Clean contaminated floors and objects thoroughly with water and detergents, observing environmental regulations. Collect waste in suitable containers, which can be labeled and sealed. Incinerate or take to a special waste disposal site in accordance with local authority regulations.

6.4. Reference to other sections
Information regarding exposure controls/personal protection and disposal considerations can be found in section 8 and 13.

Handling and storage

7.1. Precautions for safe handling
Product should be worked up in closed equipment as far as possible. Ensure thorough ventilation of stores and work areas. Handle in accordance with good industrial hygiene and safety practice. When using do not eat, drink or smoke. Hands and/or face should be washed before breaks and at the end of the shift.

Protection against fire and explosion:
Vapours may form explosive mixture with air. Prevent electrostatic charge - sources of ignition should be kept well clear - fire extinguishers should be kept handy.

7.2. Conditions for safe storage, including any incompatibilities
Segregate from acids and acid forming substances.
Further information on storage conditions: Keep container tightly closed. Avoid all sources of ignition: heat, sparks, open flame.

Storage stability:
Storage temperature: 20 °C
Storage duration: >= 24 Months
From the data on storage duration in this safety data sheet no agreed statement regarding the warrantee of application properties can be deduced.

7.3. Specific end use(s)
See exposure scenario(s) in the attachment to this safety data sheet.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

8.1. Control parameters

Components with occupational exposure limits

No occupational exposure limits known.

PNEC
freshwater: 0.0181 mg/l

marine water: 0.0018 mg/l

intermittent release: 0.181 mg/l

STP: 0.4 mg/l

sediment (freshwater): 0.0941 mg/kg

sediment (marine water): 0.00941 mg/kg

soil: 0.00818 mg/kg

oral (secondary poisoning):
No PNEC oral derived, as accumulation in organisms is not to be expected.


DNEL
worker:
Long-term exposure- systemic effects, Inhalation: 1.6 mg/m3

worker:
Long-term exposure- systemic effects, dermal: 0.23 mg/kg


8.2. Exposure controls
Personal protective equipment
Respiratory protection:
Respiratory protection in case of vapour/aerosol release. Particle filter with high efficiency for solid and liquid particles (e.g. EN 143 or 149, Type P3 or FFP3).

Suitable respiratory protection for higher concentrations or long-term effect: Self-contained breathing apparatus.

Hand protection:
Chemical resistant protective gloves (EN 374)
Suitable materials also with prolonged, direct contact (Recommended: Protective index 6, corresponding > 480 minutes of permeation time according to EN 374):
butyl rubber (butyl) - 0.7 mm coating thickness
fluoroelastomer (FKM) - 0.7 mm coating thickness
Manufacturer's directions for use should be observed because of great diversity of types.

Supplementary note: The specifications are based on tests, literature data and information of glove manufacturers or are derived from similar substances by analogy. Due to many conditions (e.g. temperature) it must be considered, that the practical usage of a chemical-protective glove in practice may be much shorter than the permeation time determined through testing.

Eye protection:
Tightly fitting safety goggles (cage goggles) (e.g. EN 166) and face shield.

Body protection:
Body protection must be chosen depending on activity and possible exposure, e.g. apron, protecting boots, chemical-protection suit (according to EN 14605 in case of splashes or EN ISO 13982 in case of dust).

General safety and hygiene measures
Handle in accordance with good industrial hygiene and safety practice. Wearing of closed work clothing is required additionally to the stated personal protection equipment. Do not breathe vapour/spray. Avoid contact with the skin, eyes and clothing. Take off immediately all contaminated clothing. Store work clothing separately.

Stability and reactivity

10.1. Reactivity
No hazardous reactions if stored and handled as prescribed/indicated.


Corrosion to metals:
Corrosive effects to metal are not anticipated. In the presence of water or moisture metal corrosion cannot be excluded.
Formation of flammable gases: Remarks: Forms no flammable gases in the presence of water.


10.2. Chemical stability
The product is stable if stored and handled as prescribed/indicated.

10.3. Possibility of hazardous reactions
Reacts with acids and strong oxidizing agents. Strong exothermic reaction.


10.4. Conditions to avoid
Avoid all sources of ignition: heat, sparks, open flame. See MSDS section 7 - Handling and storage.

10.5. Incompatible materials

Substances to avoid:
strong acids, strong oxidizing agents, nitrosating agents

10.6. Hazardous decomposition products

Hazardous decomposition products:
carbon monoxide, Carbon dioxide
nitrogen oxides, nitrous gases

Disposal considerations

13.1. Waste treatment methods

Incinerate in suitable incineration plant, observing local authority regulations.

A waste code in accordance with the European waste catalog (EWC) cannot be specified, due to dependence on the usage.
The waste code in accordance with the European waste catalog (EWC) must be specified in cooperation with disposal agency/manufacturer/authorities.


Contaminated packaging:
Contaminated packaging should be emptied as far as possible; then it can be passed on for recycling after being thoroughly cleaned.