Registration Dossier

Administrative data

First-aid measures

Description of first aid measures
After inhalation: fresh air.
After skin contact: wash off with plenty of water. Remove contaminated clothing.
After eye contact: rinse out with plenty of water.
After swallowing: immediately make victim drink water (two glasses at most). Consult a physician.
Most important symptoms and effects, both acute and delayed
irritant effects, Cough, Shortness of breath, Diarrhoea, Nausea, Vomiting, CNS disorders, confusion, paralysis symptoms
Indication of any immediate medical attention and special treatment needed
No information available.

Fire-fighting measures

Extinguishing media
Suitable extinguishing media
Water, Carbon dioxide (CO2), Foam, Dry powder
Unsuitable extinguishing media
For this substance/mixture no limitations of extinguishing agents are given.
Special hazards arising from the substance or mixture
Combustible.
Development of hazardous combustion gases or vapours possible in the event of fire.
Fire may cause evolution of:
nitrogen oxides
Advice for firefighters
Special protective equipment for firefighters
In the event of fire, wear self-contained breathing apparatus.
Further information
Suppress (knock down) gases/vapours/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system.

Accidental release measures

Personal precautions, protective equipment and emergency procedures
Advice for non-emergency personnel: Avoid substance contact. Avoid inhalation of dusts. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.
Advice for emergency responders: Protective equipment see SDS section 8.
Environmental precautions
Do not empty into drains.

Handling and storage

Precautions for safe handling
Advice on safe handling
Observe label precautions.
Hygiene measures
Change contaminated clothing. Preventive skin protection recommended. Wash hands after working with substance.
Conditions for safe storage, including any incompatibilities
Storage conditions
Tightly closed. Dry. Protected from light.
Store at +15°C to +25°C.
Specific end use(s)
Apart from the uses mentioned in section 1.2 of the SDS no other specific uses are stipulated.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Control parameters
Contains no substances with occupational exposure limit values.
Exposure controls
Engineering measures
Technical measures and appropriate working operations should be given priority over the use of personal protective equipment.
See SDS section 7.1.
Individual protection measures
Protective clothing needs to be selected specifically for the workplace, depending on concentrations and quantities of the hazardous substances handled. The chemical resistance of the protective equipment should be enquired at the respective supplier.
Eye/face protection
Safety glasses
Hand protection
full contact:
Glove material: Nitrile rubber
Glove thickness: 0.11 mm
Break through time: > 480 min
splash contact:
Glove material: Nitrile rubber
Glove thickness: 0.11 mm
Break through time: > 480 min
The protective gloves to be used must comply with the specifications of EC Directive 89/686/EEC and the related standard EN374, for example KCL 741 Dermatril® L (full contact), KCL 741 Dermatril® L (splash contact).
The breakthrough times stated above were determined by KCL in laboratory tests acc. to EN374 with samples of the recommended glove types.
This recommendation applies only to the product stated in the safety data sheet<(>,<)> supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).
Other protective equipment
protective clothing
Respiratory protection
required when dusts are generated.
Recommended Filter type: Filter P 2 (acc. to DIN 3181) for solid and liquid particles of harmful substances
The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.
Environmental exposure controls
Do not empty into drains.

Stability and reactivity

Reactivity
The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed.
Chemical stability
Sensitivity to light
Possibility of hazardous reactions
Violent reactions possible with:
Strong oxidizing agents, Strong acids
Conditions to avoid
no information available
Incompatible materials
no information available
Hazardous decomposition products
in the event of fire: See SDS section 5.

Disposal considerations

Waste treatment methods
Waste material must be disposed of in accordance with the Directive on waste 2008/98/EC as well as other national and local regulations. Leave chemicals in original containers. No mixing with other waste. Handle uncleaned containers like the product itself.
Contact us if you have further questions.