Registration Dossier

Administrative data

First-aid measures

Description of first aid measures:

General: If irritation or other symptoms occur or persist from any route of exposure, remove the affected individual from the area: see a physician/get medical attention.
Eye contact: Any material that contacts the eye should be washed out immediately with water. Get medical attention if symptoms occur.
Skin contact: Wash the affected area thoroughly with plenty of soap and water. Get medical attention if symptoms occur.
Inhalation: If affected, remove to fresh air. Get medical attention if symptoms occur.
Ingestion: Do not induce vomiting. Never give anything by mouth to an unconscious person. Rinse out the mouth with water. Get medical attention immediately.
Protection of first aid responders: Wear proper personal protective clothing and equipment.

Most important symptoms and effects, both acute and delayed:

Irritation. Pre-existing skin problems may be aggravated by prolonged or repeated contact. See section 11 for additional
information.

Indication of any immediate medical attention and special treatment needed:

Treat symptomatically

Fire-fighting measures

Extinguishing media:

Suitable: Use water spray, ABC dry chemical, foam or carbon dioxide. Water or foam may cause frothing. Use water to keep fire-exposed containers cool. Water spray may be used to flush spills away from exposures.
Unsuitable: None known.

Special hazards arising from substance or mixture:

Unusual fire/explosion hazards: Product is not considered a fire hazard, but will burn if ignited. Closed container may rupture (due to build up in pressure) when exposed to extreme heat.
Hazardous combustion products: Irritating or toxic substances will be emitted upon burning, combustion or decomposition.

Advice for fire-fighters:

Wear self-contained breathing apparatus (SCBA) equipped with a full facepiece and operated in a pressure-demand mode (or other positive pressure mode) and approved protective clothing. Personnel without suitable respiratory protection must leave the area to prevent significant exposure to hazardous gases from combustion, burning or decomposition. In an enclosed or poorly ventilated area, wear SCBA during cleanup immediately after a fire as well as during the attack phase of firefighting operations.

Accidental release measures

Personal precautions, protective equipment and emergency procedures:

Use of recommended personal protective equipment. If spilled in an enclosed area, ventilate. Eliminate ignition sources.

Environmental precautions:

Do not flush product into public sewer, water systems or surface waters.

Methods and material for containment and cleaning up:

Contain by diking with sand, earth or other non-combustible material. Wear proper personal protective clothing and equipment. Absorb spill with an inert material. Place into labeled, closed container; store in safe location to await disposal. Change contaminated clothing and launder before reuse.

Handling and storage

Precautions for safe handling:

As with any chemical product, use good laboratory/workplace procedures. Do not cut, puncture, or weld on or near the container. Use under well-ventilated conditions. Wash thoroughly after handling this product. Always wash up before eating, smoking or using the facilities. Avoid eye contact. Avoid repeated or prolonged skin contact. Avoid inhalation of aerosol, mist, spray, fume or vapor. Avoid drinking, tasting, swallowing or ingesting this product. Wash contaminated clothing before reuse. Provide eyewash fountains and safety showers in the work area.

Conditions for safe storage, including any incompatibilities:

Keep away from heat, sparks and open flames. Store cool and dry, under well-ventilated conditions. Store this material away from incompatible substances . Do not store in open, unlabeled or mislabeled containers. Keep container closed when not in use. Empty container contains residual product which may exhibit hazards of product. Do not reuse empty container without commercial cleaning or reconditioning. Plasticizer products will soften plastic materials and as a result they should not be transported in piping systems constructed from these materials.

Specific end use(s):

No Additional Information.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Control parameters:

Occupational exposure limits: No applicable exposure limits.
Derived No Effect Levels (DNELs) - Workers: Not Available
Predicted No Effect Concentration (PNECs): Not Available

Exposure controls:

Appropriate engineering controls: Always provide effective general and, when necessary, local exhaust ventilation to draw spray, aerosol, fume, mist and vapor away from workers to prevent routine inhalation. Ventilation must be adequate to maintain the ambient workplace atmosphere below the exposure limit(s) outlined in the SDS.

Individual protection measures, such as personal protective equipment:

Eye/face protection: Wear eye protection.
Hand protection: Avoid skin contact when mixing or handling the material by wearing impervious and chemical resistant gloves. In case of prolonged immersion or frequently repeated contact, gloves with breakthrough times greater than 240 minutes (protection class 5 or greater) are recommended. For brief contact or splash applications, gloves with breakthrough times of 10 minutes or greater are recommended (protection class 1 or greater). The protective gloves to be used must comply with the specifications of the EC directive 89/686/EEC and the resultant standard EN 374. Suitability and durability of a glove is dependent on usage (e.g. frequency and duration of contact, other chemicals which may be handled, chemical resistance of
glove material and dexterity). Always seek advice of the glove supplier as to the most suitable glove material.
Skin and body protection: Use good laboratory/workplace procedures including personal protective clothing: labcoat, safety glasses and protective gloves.
Respiratory protection: In case of insufficient ventilation, wear suitable respiratory equipment.
Further information: Eyewash fountains and safety showers are recommended in the work area.

Environmental exposure controls: See Sections Accidental release measures and Ecological information.

Stability and reactivity

Reactivity: None known.
Chemical stability: This product is stable.
Possibility of hazardous reactions: Hazardous polymerization will not occur.
Conditions to avoid: Excessive heat and ignition sources.
Incompatible materials: Avoid oxidizing agents and reducing agents.
Hazardous decomposition products: Carbon dioxide, carbon monoxide and hydrocarbons.

Disposal considerations

Waste treatment methods:

Dispose of unused contents (incineration) in accordance with national and local regulations. Dispose of container in accordance with national and local regulations. Ensure the use of properly authorized waste management companies, where appropriate.