Registration Dossier

Guidance on Safe Use

Guidance on Safe Use

Currently viewing:

Administrative data

First-aid measures

· General information:
Immediately remove any clothing soiled by the product.
Take note of the following instructions.
· After inhalation: Supply fresh air; consult doctor in case of complaints.
· After skin contact:
Immediately rinse with water.
If skin irritation occurs, consult a doctor.
· After eye contact:
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
· After swallowing: Do not induce vomiting; call for medical help immediately.

Fire-fighting measures

· Suitable extinguishing agents: Use fire extinguishing methods suitable to surrounding conditions.
· For safety reasons unsuitable extinguishing agents: Water with full jet
· Special hazards caused by the substance, its products of combustion or resulting gases:
Carbon monoxide and carbon dioxide
Metal oxide fume
· Protective equipment:
Wear protective equipment.
Mount respiratory protective device.
· Additional information
Dispose of fire debris and contaminated fire fighting water in accordance with official regulations.
Collect contaminated fire fighting water separately. It must not enter the sewage system.

Accidental release measures

· Person-related safety precautions: Wear protective clothing.
· Measures for environmental protection: Do not allow to enter sewers/ surface or ground water.
· Measures for cleaning/collecting:
Sweep the spill area; avoid raising dust.
Clean the affected area carefully; suitable cleaners are:
Use appropriate industrial vacuum cleaners or central vacuum systems for dust removal.
Ensure adequate ventilation.
Dispose contaminated material as waste: see "disposal considerations".
· Additional information:
for information on safe handling: see "handling and storage"
for information on personal protection equipment: see "exposure controls / personal protection"
for disposal information: see "disposal considerations".

Handling and storage

· Handling:
· Information for safe handling:
Keep receptacles tightly sealed.
Avoid formation of respirable particles.
Prevent formation of dust.
· Information about fire - and explosion protection: The product is not flammable.
· Storage:
· Requirements to be met by storerooms and receptacles: Store only in the original container.
· Information about storage in one common storage facility:
Store away from foodstuffs.
Do not store together with acids.
Store away from water.
· Further information about storage conditions:
This product is hygroscopic.
Protect from humidity and water.
Store in cool, dry conditions in well sealed receptacles.

Transport information

Land transport (ADR/RID)

Shippingopen allclose all
Class:
no classification
SpecialProvisionsopen allclose all

Inland waterway transport (ADN(R))

Shippingopen allclose all
Class:
no classification
Remarksopen allclose all

Marine transport (IMDG)

Class:
no classification
Remarksopen allclose all

Air transport ICAO/IATA

Class:
no classification
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

· Additional information about design of technical facilities: No further data; see "handling and storage".
· Ingredients with limit values that require monitoring at the workplace:
Samarium oxide, CAS 12060-58-1
AGW (Germany) Long-term value: *3 **10 mg/m³
2(II); *alveolengängig **einatembare Fraktion; AGS
· Additional information: Based on lists valid at date of MSDS creation.
· Personal protective equipment:
· General protective and hygienic measures:
Keep away from foodstuffs, beverages and feed.
Immediately remove all soiled and contaminated clothing.
Wash hands before breaks and at the end of work.
Avoid contact with the eyes and skin.
Do not inhale dust / smoke / mist.
Respiratory protection:
If the WEL value is exceeded.
Filter P2
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device.
· Protection of hands:
Avoid direct contact with the chemical/ the product/ the preparation by organizational measures.
Protective gloves.
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Preventive skin protection by use of skin-protecting agents is recommended.
Check the condition of the gloves prior to each use.
Wear gloves for protection against mechanical hazards according to EN 388.
Use gloves of stable material (e.g. Nitrile) - if necessary tricoted to improve the wearability.
· Material of gloves
Recommended thickness of the material: ≥ 0.35 mm
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application.
Penetration time of glove material
EN 420: Minimum requirements for efficiency level 1 for all groups.
For the mixture of chemicals mentioned below the penetration time has to be at least 480 minutes (Permeation according to EN 374 Part 3: Level 6).
The exact break through time has to be obtained from the manufacturer of the protective gloves and has to be observed.
· For the permanent contact in work areas without heightened risk of injury (e.g. Laboratory) gloves made of the following material are suitable:
Butyl rubber, BR
Nitrile rubber, NBR
· Not suitable are gloves made of the following materials:
Strong material gloves
Leather gloves
· Eye protection:
Safety glasses.
· Body protection: Protective work clothing.

Stability and reactivity

· Thermal decomposition / conditions to be avoided:
No decomposition if used according to specifications.
· Dangerous decomposition products:
Metal oxide smoke

Disposal considerations

· Product:
· Recommendation: Disposal must be made according to official regulations.
· Waste disposal key:
The disposal of the product has to be carried out in accordance with the legal requirements. EWC waste codes are strictly industry-oriented, therefore waste classification has to be done by the waste producer.
· Uncleaned packaging:
· Recommendation: Disposal must be made according to official regulations.