Registration Dossier

Administrative data

First-aid measures

Immediately remove contaminated clothing. If the patient is likely to become unconscious, place and
transport in stable sideways position (recovery position). First aid personnel should pay attention to
their own safety.
If inhaled:
If difficulties occur after vapour/aerosol has been inhaled, remove to fresh air and seek medical
attention.
On skin contact:
Wash thoroughly with soap and water.
On contact with eyes:
Immediately wash affected eyes for at least 15 minutes under running water with eyelids held open,
consult an eye specialist.
On ingestion:
Immediately rinse mouth and then drink plenty of water, do not induce vomiting, seek medical
attention.

Fire-fighting measures

5.1. Extinguishing media
Suitable extinguishing media:
water spray, dry powder, foam
Unsuitable extinguishing media for safety reasons:
water jet
5.2. Special hazards arising from the substance or mixture
harmful vapours
Evolution of fumes/fog. The substances/groups of substances mentioned can be released in case of
fire.
5.3. Advice for fire-fighters
Special protective equipment:
Wear a self-contained breathing apparatus.
Further information:
The degree of risk is governed by the burning substance and the fire conditions. Contaminated
extinguishing water must be disposed of in accordance with official regulations.

Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures
Use personal protective clothing. Breathing protection required. Avoid contact with the substance.
6.2. Environmental precautions
Contain contaminated water/firefighting water. Do not discharge into drains/surface
waters/groundwater. Discharge into the environment must be avoided.
6.3. Methods and material for containment and cleaning up
For large amounts: Pump off product.
For residues: Pick up with suitable absorbent material. Dispose of absorbed material in accordance
with regulations.

Handling and storage

7.1. Precautions for safe handling
Avoid all direct contact with the substance/product. Avoid contact with the skin, eyes and clothing.
Wear suitable protective clothing and gloves.
Containers must only be opened under local exhaust ventilation. Ensure adequate ventilation.
Protection against fire and explosion:
Take precautionary measures against static discharges.
7.2. Conditions for safe storage, including any incompatibilities
Further information on storage conditions: Keep container tightly closed and dry; store in a cool
place.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Personal protective equipment
Respiratory protection:
Suitable respiratory protection for higher concentrations or long-term effect: Gas filter for
gases/vapours of organic compounds (boiling point >65 °C, e. g. EN 14387 Type A)
Hand protection:
Chemical resistant protective gloves (EN 374)
Suitable materials also with prolonged, direct contact (Recommended: Protective index 6,
corresponding > 480 minutes of permeation time according to EN 374):
fluoroelastomer (FKM) - 0.7 mm coating thickness
Polyethylene-Laminate (PE laminate) - ca. 0.1 mm coating thickness
Suitable materials short-term contact and/or splashes (recommended: At least protective index 2,
corresponding > 30 minutes of permeation time according to EN 374)
nitrile rubber (NBR) - 0.4 mm coating thickness
Supplementary note: The specifications are based on tests, literature data and information of glove
manufacturers or are derived from similar substances by analogy. Due to many conditions (e.g.
temperature) it must be considered, that the practical usage of a chemical-protective glove in
practice may be much shorter than the permeation time determined through testing.
Manufacturer's directions for use should be observed because of great diversity of types.
Eye protection:
Tightly fitting safety goggles (cage goggles) (e.g. EN 166) and face shield.
Body protection:
Body protection must be chosen depending on activity and possible exposure, e.g. apron, protecting
boots, chemical-protection suit (according to EN 14605 in case of splashes or EN ISO 13982 in case
of dust).
General safety and hygiene measures
Handle in accordance with good industrial hygiene and safety practice. Wearing of closed work
clothing is required additionally to the stated personal protection equipment. Avoid all contact with
the substance.

Stability and reactivity

10.1. Reactivity
No hazardous reactions if stored and handled as prescribed/indicated.
Corrosion to metals: No corrosive effect on metal.
Reactions with
water/air:
Reaction with: water
Flammable gases: no
Toxic gases: no
Corrosive gases: no
Smoke or fog: no
Peroxides: no
Reaction with: air
Flammable gases: no
Toxic gases: no
Corrosive gases: no
Smoke or fog: no
Peroxides: no
10.2. Chemical stability
The product is stable if stored and handled as prescribed/indicated.
Peroxides: 0.000 %
The product does not contain peroxides.
10.3. Possibility of hazardous reactions
No hazardous reactions when stored and handled according to instructions.
10.4. Conditions to avoid
Avoid all sources of ignition: heat, sparks, open flame. Avoid electro-static discharge.
10.5. Incompatible materials
Substances to avoid:
oxidizing agents
10.6. Hazardous decomposition products
Hazardous decomposition products:
No hazardous decomposition products if stored and handled as prescribed/indicated.

Disposal considerations

13.1. Waste treatment methods
Must be disposed of or incinerated in accordance with local regulations.
Contaminated packaging:
Uncontaminated packaging can be re-used.
Packs that cannot be cleaned should be disposed of in the same manner as the contents.