Registration Dossier

Administrative data

First-aid measures

Eye Contact: Flush with water while holding eyelids open for at least 15 minutes. Seek medical attention immediately.
Skin Contact: Remove contaminated clothing. Flush area with large amounts of water. Use soap. Seek medical attention.
Ingestion: Never give anything by mouth to an unconscious person. Wash out mouth with water. Do not induce vomiting unless directed by medical personnel. Seek medical attention immediately.
Inhalation: Remove to fresh air and keep patient at rest. Seek medical attention immediately.
Symptoms and Effects of Exposure: For information on potential signs and symptoms of exposure

Fire-fighting measures

Extinguishing Media: Use carbon dioxide, dry chemical, or water spray.
Hazardous Combustion Products: Formation of toxic gases is possible during heating or fire.
Fire Fighting Procedures: During all fire fighting activities, wear appropriate protective equipment, including selfcontained breathing apparatus.
Fire / Explosion Hazards: Fine particles (such as dust and mists) may fuel fires/explosions.

Accidental release measures

Health and Safety Precautions: Personnel involved in clean-up should wear appropriate personal protective equipment (see Section 8). Minimize exposure.
Measures for Cleaning / Collecting: Contain the source of spill if it is safe to do so. Collect spilled material by a method that controls dust generation.A damp cloth or a filtered vacuum should be used to clean spills of dry solids. Clean spill area thoroughly.
Measures for Environmental Protections: Place waste in an appropriately labeled, sealed container for disposal. Care should be taken to avoid environmental release.

Handling and storage

General Handling: Ground and bond all bulk transfer equipment. Avoid open handling. Minimize dust generation. Use local exhaust ventilation or perform work under fume hood/fume cupboard. Avoid inhalation and contact with skin, eye, and clothing. When handling, use appropriate personal protective equipment (see Section 8). Wash hands and any exposed skin after removal of PPE. Releases to the environment should be avoided. Review and implement appropriate technical and procedural waste water and waste disposal measures to prevent occupational exposure or environmental releases. Potential points of process emissions of this material to the atmosphere should be controlled with dust collectors, HEPA filtration systems or other equivalent controls. Refer to Ecological Information, for information on potential effects on the environment.
Storage Conditions: Store at room temperature in properly labeled containers. Keep away from heat, sparks and flames.

Transport information

Land transport (ADR/RID)

UN number:
Not regulated for transport .
Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (ADN(R))

UN number:
Not regulated for transport .
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

UN number:
Not regulated for transport .
Remarksopen allclose all

Air transport ICAO/IATA

UN number:
Not regulated for transport .
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Analytical Method: Analytical method available. Contact Pfizer Inc for further information.
Engineering Controls: Engineering controls should be used as the primary means to control exposures. Use process containment, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits.
Environmental Exposure Controls: Refer to specific Member State legislation for requirements under Community environmental legislation.
Personal Protective Equipment: Refer to applicable national standards and regulations in the selection and use of personal protective equipment (PPE).
Hands: Wear impervious gloves as minimum protection.
Eyes: Wear safety glasses as minimum protection.
Skin: Wear impervious protective clothing when handling this compound.
Respiratory protection: If the applicable Occupational Exposure Limit (OEL) is exceeded, wear an appropriate respirator with a protection factor sufficient to control exposures to below the OEL.

Stability and reactivity

Chemical Stability: Stable under normal conditions of use.
Conditions to Avoid: Eliminate possible ignition sources (e.g., heat, sparks, flame, impact, friction, electrostatic discharge).
Incompatible Materials: As a precautionary measure, keep away from strong oxidizers

Disposal considerations

Waste Treatment Methods: Dispose of waste in accordance with all applicable laws and regulations. Member State specific and Community specific provisions must be considered. Considering the relevant known environmental and human health hazards of the material, review and implement appropriate technical and procedural waste water and waste disposal measures to prevent occupational exposure and environmental release. It is recommended that waste minimization be practiced. The best available technology should be utilized to prevent environmental releases. This may include destructive techniques for waste and wastewater.