Registration Dossier

Diss Factsheets

Administrative data

First-aid measures

· 4.1 Description of first aid measures
· General information Remove contaminated clothing.
· After inhalation Supply fresh air; consult doctor in case of symptoms.
· After skin contact
Immediately wash with water and soap and rinse thoroughly.
If skin irritation continues, consult a doctor.
· After eye contact
Rinse opened eye for several minutes under running water. If symptoms persist, consult doctor.
· After swallowing Drink copious amounts of water and provide fresh air. Instantly call for doctor.
· 4.2 Most important symptoms and effects, both acute and delayed
No further relevant information available.
· 4.3 Indication of any immediate medical attention and special treatment needed
No further relevant information available.
* SECTION 5: Firefighting measures

Fire-fighting measures

· 5.1 Extinguishing media
· Suitable extinguishing agents Use fire fighting measures that suit the environment.
· 5.2 Special hazards arising from the substance or mixture
Formation of toxic gases is possible during heating or in case of fire.
- Phosphorus oxides
· 5.3 Advice for firefighters
· Protective equipment: Do not inhale explosion gases or combustion gases.

Accidental release measures

· 6.1 Personal precautions, protective equipment and emergency procedures
Wear protective clothing.
· 6.2 Environmental precautions: Do not allow product to reach sewage system or water bodies.
· 6.3 Methods and material for containment and cleaning up:
Collect mechanically.
Dispose of contaminated material as waste according to item 13.
Ensure adequate ventilation.
· 6.4 Reference to other sections
See Section 7 for information on safe handling
See Section 8 for information on personal protection equipment.
See Section 13 for information on disposal.

Handling and storage

· 7.1 Precautions for safe handling
Prevent formation of dust.
Use only in well ventilated areas.
· Information about protection against explosions and fires: Protect from heat.
· 7.2 Conditions for safe storage, including any incompatibilities
· Storage
· Requirements to be met by storerooms and containers: No special requirements.
· Information about storage in one common storage facility: Not required.
· Further information about storage conditions:
Keep container tightly sealed.
Protect from heat and direct sunlight.
Store under dry conditions.
· Storage class LGK 10-13
· 7.3 Specific end use(s) No further relevant information available.

Transport information

Land transport (UN RTDG/ADR/RID)

UN number:
Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (UN RTDG/ADN(R))

UN number:
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

UN number:
Shipping information
Proper shipping name and description:
Chemical name:
Remarksopen allclose all

Air transport (UN RTDG/ICAO/IATA)

UN number:
Shipping information
Proper shipping name and description:
Chemical name:
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

· Additional information about design of technical systems: No further data; see item 7.
· 8.1 Control parameters
· Components with limit values that require monitoring at the workplace: Not required.
· Additional information: The lists that were valid during the compilation were used as basis.
· 8.2 Exposure controls
· Personal protective equipment
· General protective and hygienic measures
Do not eat, drink or smoke while working.
Keep away from foodstuffs, beverages and food.
Take off immediately all contaminated clothing
Wash hands during breaks and at the end of the work.
Avoid contact with the eyes and skin.
· Breathing equipment:
Short term filter device:
Filter P1.
· Protection of hands:
Protective gloves.
The glove material has to be impermeable and resistant to the product/ the substance/ the
Selection of the glove material on consideration of the penetration times, rates of diffusion and the
· Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks
of quality and varies from manufacturer to manufacturer.
· Penetration time of glove material
The exact break trough time has to be found out by the manufacturer of the protective gloves and
has to be observed.
· Eye protection: Tightly sealed safety glasses.
· Body protection: Protective work clothing.

Stability and reactivity

10.1 Reactivity No further relevant information available.
· 10.2 Chemical stability
· Thermal decomposition / conditions to be avoided:
No decomposition if used according to specifications.
· 10.3 Possibility of hazardous reactions
Reacts with strong acids
Develops toxic gases / fumes
· 10.4 Conditions to avoid No further relevant information available.
· 10.5 Incompatible materials: No further relevant information available.
· 10.6 Hazardous decomposition products: Phosphorus oxides (e.g. P2O5)

Disposal considerations

· 13.1 Waste treatment methods
· Recommendation Must be specially treated under adherence to official regulations.
· Uncleaned packagings:
· Recommendation: Disposal must be made according to official regulations.
· Recommended cleaning agent: Water, if necessary with cleaning agent.

Categories Display