Registration Dossier

Administrative data

First-aid measures

Description of first aid measures.
EYES: Remove contact lenses, if present. Wash immediately with plenty of water for at least 15 minutes, opening the eyelids fully. If problem
persists, seek medical advice.
SKIN: Remove contaminated clothing. Wash immediately with plenty of water. If irritation persists, get medical advice/attention. Wash
contaminated clothing before using it again.
INHALATION: Remove to open air. In the event of breathing difficulties, get medical advice/attention immediately.
INGESTION: Get medical advice/attention. Induce vomiting only if indicated by the doctor. Never give anything by mouth to an unconscious
person, unless authorised by a doctor.

Most important symptoms and effects, both acute and delayed.
For symptoms and effects caused by the contained substances, see section of toxicological information.


Indication of any immediate medical attention and special treatment needed.
Information not available.

Fire-fighting measures

Extinguishing media.
SUITABLE EXTINGUISHING EQUIPMENT
The extinguishing equipment should be of the conventional kind: carbon dioxide, foam, powder and water spray.
UNSUITABLE EXTINGUISHING EQUIPMENT
None in particular.

Special hazards arising from the substance or mixture.
HAZARDS CAUSED BY EXPOSURE IN THE EVENT OF FIRE
Do not breathe combustion products.

Advice for firefighters.
GENERAL INFORMATION
Use jets of water to cool the containers to prevent product decomposition and the development of substances potentially hazardous for health.
Always wear full fire prevention gear. Collect extinguishing water to prevent it from draining into the sewer system. Dispose of contaminated
water used for extinction and the remains of the fire according to applicable regulations.

Accidental release measures

Personal precautions, protective equipment and emergency procedures.
Block the leakage if there is no hazard.
Wear suitable protective equipment (including personal protective equipment referred to section 'Exposure control/personal protection' of the safety data sheet) to prevent any contamination of skin, eyes and personal clothing. These indications apply for both processing staff and those involved in emergency
procedures.

Environmental precautions.
The product must not penetrate into the sewer system or come into contact with surface water or ground water.

Methods and material for containment and cleaning up.
Collect the leaked product into a suitable container. Evaluate the compatibility of the container to be used, by checking section 'Stability and reactivity'.
Absorb the remainder with inert absorbent material.
Make sure the leakage site is well aired. Check incompatibility for container material in section Handling and storage. Contaminated material should be
disposedof in compliance with the provisions set forth in section 'Disposal considerations'.

Reference to other sections.
Any information on personal protection and disposal is given in sections 'Exposure control/personal protection' and in section 'Disposal considerations'.

Handling and storage

Precautions for safe handling.
Before handling the product, consult all the other sections of this material safety data sheet. Avoid leakage of the product into the
environment. Do not eat, drink or smoke during use. Remove any contaminated clothes and personal protective equipment before entering
places in which people eat.

Conditions for safe storage, including any incompatibilities.
Store only in the original container. Store the containers sealed, in a well ventilated place, away from direct sunlight. Keep containers away
from any incompatible materials, see section 'Stability and reactivity' for details.

Specific end use(s).
Information not available.

Transport information

Land transport (ADR/RID)

UN number:
Not applicable
Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (ADN(R))

UN number:
Not applicable
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

UN number:
Not applicable
Remarksopen allclose all

Air transport ICAO/IATA

UN number:
Not applicable
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Control parameters.
Information not available.

Exposure controls.
As the use of adequate technical equipment must always take priority over personal protective equipment, make sure that the workplace is
well aired through effective local aspiration. Personal protective equipment must be CE marked, showing that it complies with applicable
standards.
Provide an emergency shower with face and eye wash station.

HAND PROTECTION
Protect hands with category III work gloves (see standard EN 374).
The following should be considered when choosing work glove material: compatibility, degradation, failure time and permeability.
The work gloves' resistance to chemical agents should be checked before use, as it can be unpredictable. The gloves' wear time depends on
the duration and type of use.

SKIN PROTECTION
Wear category II professional long-sleeved overalls and safety footwear (see Directive 89/686/EEC and standard EN ISO 20344). Wash body
with soap and water after removing protective clothing.

EYE PROTECTION
Wear airtight protective goggles (see standard EN 166).
In the presence of risks of exposure to splashes or squirts during work, adequate mouth, nose and eye protection should be used to prevent
accidental absorption.

RESPIRATORY PROTECTION
If the threshold value (e.g. TLV-TWA) is exceeded for the substance or one of the substances present in the product, use a mask with a type
B filter whose class (1, 2 or 3) must be chosen according to the limit of use concentration. (see standard EN 14387). In the presence of gases
or vapours of various kinds and/or gases or vapours containing particulate (aerosol sprays, fumes, mists, etc.) combined filters are required.
Respiratory protection devices must be used if the technical measures adopted are not suitable for restricting the worker's exposure to the
threshold values considered. The protection provided by masks is in any case limited.
If the substance considered is odourless or its olfactory threshold is higher than the corresponding TLV-TWA and in the case of an
emergency, wear open-circuit compressed air breathing apparatus (in compliance with standard EN 137) or external air-intake breathing
apparatus (in compliance with standard EN 138). For a correct choice of respiratory protection device, see standard EN 529.
ENVIRONMENTAL EXPOSURE CONTROLS.
The emissions generated by manufacturing processes, including those generated by ventilation equipment, should be checked to ensure
compliance with environmental standards.
Product residues must not be indiscriminately disposed of with waste water or by dumping in waterways.

Stability and reactivity

Reactivity.
There are no particular risks of reaction with other substances in normal conditions of use.

Chemical stability.
The product is stable in normal conditions of use and storage.

Possibility of hazardous reactions.
No hazardous reactions are foreseeable in normal conditions of use and storage.

Conditions to avoid.
None in particular. However the usual precautions used for chemical products should be respected.

Incompatible materials.
Information not available.

Hazardous decomposition products.
Information not available.

Disposal considerations

Waste treatment methods.
Reuse, when possible. Product residues should be considered special hazardous waste. The hazard level of waste containing this product
should be evaluated according to applicable regulations.
Disposal must be performed through an authorised waste management firm, in compliance with national and local regulations.
CONTAMINATED PACKAGING
Contaminated packaging must be recovered or disposed of in compliance with national waste management regulations