Registration Dossier

Administrative data

First-aid measures

Description of first aid measures
If inhaled:fresh air.

In case of skin contact:
Take off immediately all contaminated clothing. Rinse skin with water/ shower.
Consult a physician.

In case of eye contact:
rinse out with plenty of water.
Remove contact lenses.

If swallowed: immediately make victim drink water (two glasses at most).
Consult a physician.

Most important symptoms and effects, both acute and delayed
Allergic reactions

Indication of any immediate medical attention and special treatment needed
No information available

Fire-fighting measures

Extinguishing media
Suitable extinguishing media:
Carbon dioxide (CO2)
Dry powder

Unsuitable extinguishing media:
For this substance/mixture no limitations of extinguishing agents are given.

Special hazards arising from the substance or mixture
Specific hazards during firefighting:
Development of hazardous combustion gases or vapours possible in the event of fire.
Fire may cause evolution of:
hydrogen bromide

Advice for firefighters
Special protective equipment for firefighters:
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.

Further information:
Suppress (knock down) gases/vapours/mists with a water spray jet.
Prevent fire extinguishing water from contaminating surface water or the ground water system.

Accidental release measures

Personal precautions, protective equipment and emergency procedures
Personal precautions:
Advice for non-emergency personnel:
Avoid inhalation of dusts.
Avoid substance contact.
Ensure adequate ventilation.
Evacuate the danger area, observe emergency procedures, consult an expert.
Advice for emergency responders:
Protective equipment see section 8.

Environmental precautions
Environmental precautions:
Do not flush into surface water or sanitary sewer system.

Methods and material for containment and cleaning up
Methods for cleaning up:
Cover drains. Collect, bind, and pump off spills.
Observe possible material restrictions (see sections 7 and 10).
Take up dry. Dispose of properly. Clean up affected area. Avoid generation of dusts.

Reference to other sections
Indications about waste treatment see section 13.

Handling and storage

Precautions for safe handling
Advice on safe handling:
Observe label precautions.
Hygiene measures:
Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.

Conditions for safe storage, including any incompatibilities
Further information on storage conditions:
Tightly closed. Dry.
Risks from decomposition products: see section 10.3
Recommended storage temperature:
Recommended storage temperature see product label.

7.3 Specific end use(s)
Apart from the uses mentioned in section 1.2 no other specific uses are stipulated.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Control parameters
Exposure controls
Engineering measures
Technical measures and appropriate working operations should be given priority over the use of personal protective equipment.
See section 7.1.

Personal protective equipment
Protective clothing needs to be selected specifically for the workplace, depending on concentrations and quantities of the hazardous substances handled and must meet the specifications of a standard EN/ISO/DIN. The chemical resistance of the protective equipment should be enquired at the respective supplier.

Eye protection: Safety glasses

Hand protection:
full contact
Glove material: Nitrile rubber
Glove thickness: 0,11 mm
Break through time: > 480 min

splash contact
Glove material: Nitrile rubber
Glove thickness: 0,11 mm
Break through time: > 480 min

Respiratory protection:
required when dusts are generated.
Recommended Filter type::
Filter P 2 (acc. to DIN 3181) for solid and liquid particles of harmful substances
The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.
Environmental exposure controls
General advice:
Do not flush into surface water or sanitary sewer system.

Stability and reactivity

The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed.

Chemical stability
The product is chemically stable under standard ambient conditions (room temperature) .

Possibility of hazardous reactions
Hazardous reactions:
Violent reactions possible with:
strong oxidising agents

Conditions to avoid
Conditions to avoid:
no information available

Incompatible materials
Materials to avoid:
no information available

Hazardous decomposition products
in the event of fire: See section 5.

Disposal considerations

See for processes regarding the return of chemicals and containers, or contact us there if you have further questions.