Registration Dossier

Administrative data

First-aid measures

Eye Contact: Flush with water while holding eyelids open for at least 15 minutes. Seek medical attention immediately.
Skin Contact: Remove contaminated clothing. Flush area with large amounts of water. Use soap. Seek medical attention.
Ingestion: Never give anything by mouth to an unconscious person. Wash out mouth with water. Do not induce vomiting unless directed by medical personnel. Seek medical attention immediately.
Inhalation: Remove to fresh air and keep patient at rest. Seek medical attention immediately.

Fire-fighting measures

Extinguishing Media: Extinguish fires with CO2, extinguishing powder, foam, or water.

Special Hazards Arising from the Substance or Mixture
Hazardous Combustion Products: Formation of toxic gases is possible during heating or fire. May include oxides of carbon and nitrogen.
Fire / Explosion Hazards: Strong dust explosion characteristic. Very high sensitivity of a dust cloud to ignition, based on minimum ignition energy.

Advice for Fire-Fighters
During all fire fighting activities, wear appropriate protective equipment, including self-contained breathing apparatus.

Accidental release measures

Personal Precautions, Protective Equipment and Emergency Procedures
Personnel involved in clean-up should wear appropriate personal protective equipment. Minimize exposure.

Environmental Precautions
Place waste in an appropriately labeled, sealed container for disposal. Care should be taken to avoid environmental release.

Methods and Material for Containment and Cleaning Up
Measures for Cleaning / Collecting: Contain the source of the spill if it is safe to do so. Collect spilled material by a method that controls dust generation. Avoid use of a filtered vacuum to clean spills of dry solids, due to the potential for electrostatic discharge and the strong dust explosion potential and very high sensitivity to ignition. Clean spill area thoroughly.
Additional Consideration for Large Spills: Non-essential personnel should be evacuated from affected area. Report emergency situations immediately. Clean up operations should only be undertaken by trained personnel.

Handling and storage

Precautions for Safe Handling
All conductive elements of the system that contact the dry substance should be properly bonded and grounded and equipped with proper explosion relief or suppression systems. This material should not be flowed through nonconductive ducts or pipes because of the potential for electrostatic discharge ignition. Restricting the use of high resistivity materials, such as plastics, should be considered. Ground and bond all bulk transfer equipment. Avoid open handling. Minimize dust generation. Use local exhaust ventilation or perform work under fume hood/fume cupboard. Avoid inhalation and contact with skin, eye, and clothing. When handling, use appropriate personal protective equipment. Wash hands and any exposed skin after removal of PPE. Releases to the environment should be avoided. Review and implement appropriate technical and procedural waste water and waste disposal measures to prevent occupational exposure or environmental releases. Potential points of process emissions of this material to the atmosphere should be controlled with dust collectors, HEPA filtration systems or other equivalent controls.

Conditions for Safe Storage, Including any Incompatibilities
Storage Conditions: Store at room temperature in properly labeled containers. Keep away from heat, sparks and flames.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all

Additional transport information

Additional transport information
The following refers to all modes of transportation unless specified below.
Not regulated for transport under USDOT, EUADR, IATA, or IMDG regulations.

Exposure controls / personal protection

Pfizer Occupational Exposure Band (OEB): OEB 3 (control exposure to the range of 10ug/m3 to < 100ug/m3)
Engineering Controls: Engineering controls should be used as the primary means to control exposures. Use process containment, local exhaust ventilation, or other engineering controls to maintain airborne levels within the OEB range.
Personal Protective Equipment: Refer to applicable national standards and regulations in the selection and use of personal protective equipment (PPE).
Hands: Wear impervious gloves to prevent skin contact.
Eyes: Wear safety goggles as minimum protection.
Skin: Wear impervious protective clothing to prevent skin contact - consider use of disposable clothing where appropriate.
Respiratory protection: If airborne exposures are within or exceed the Occupational Exposure Band (OEB) range, wear an appropriate respirator with a protection factor sufficient to control exposures to the bottom of the OEB range.

Stability and reactivity

Chemical Stability: Stable under normal conditions of use.

Possibility of Hazardous Reactions
Oxidizing Properties: Not an oxidizing solid.
Conditions to Avoid: Fine particles (such as dust and mists) may fuel fires/explosions. Keep away from heat and other sources of ignition, including electrostatic discharge.
Incompatible Materials: As a precautionary measure, keep away from strong oxidizers

Disposal considerations

Waste Treatment Methods: Dispose of waste in accordance with all applicable laws and regulations. Member State specific and Community specific provisions must be considered. Considering the relevant known environmental and human health hazards of the material, review and implement appropriate technical and procedural waste water and waste disposal measures to prevent occupational exposure and environmental release. It is recommended that waste minimization be practiced. The best available technology should be utilized to prevent environmental releases. This may include destructive techniques for waste and wastewater.