Registration Dossier

Administrative data

First-aid measures

Measured indicated is for substance at ~85% in mineral oil, as marketed

General advice:
Move out of dangerous area.
Show this safety data sheet to the doctor in attendance.
If inhaled:
If unconscious, place in recovery position and seek medical advice.
If symptoms persist, call a physician.
In case of skin contact:
Take off contaminated clothing and shoes immediately.
Wash off with soap and plenty of water.
If symptoms persist, call a physician.
In case of burns apply cold water until pain subsides then seek medical advice.
In case of eye contact:
Flush eyes with water as a precaution.
Remove contact lenses.
Protect unharmed eye.
Keep eye wide open while rinsing.
If eye irritation persists: Get medical advice/ attention.
If swallowed:
Clean mouth with water and drink afterwards plenty of water.
Do not give milk or alcoholic beverages.
Never give anything by mouth to an unconscious person.
Obtain medical attention.

Most important symptoms and effects, both acute and delayed
Symptoms:
Allergic symptoms may develop within 12 hours after exposure.
sensitising effects
Dermatitis

Indication of any immediate medical attention and special treatment needed
Treatment:
Show this safety data sheet to the doctor in attendance.
The first aid procedure should be established in consultation with the doctor responsible for industrial medicine.
If a person vomits when lying on his back, place him in the recovery position.
Keep patient warm and at rest

Fire-fighting measures

Measured indicated is for substance at ~85% in mineral oil, as marketed

Extinguishing media
Suitable extinguishing media:
Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames
Unsuitable extinguishing media:
High volume water jet
Special hazards arising from the substance or mixture
Combustibility:
Not classified as flammable or combustible, but will combust if ignited.
Hazardous combustion products:
Nitrogen oxides (NOx)
Carbon monoxide, carbon dioxide and unburned hydrocarbons (smoke).
Flammable properties:
See Section 9 for information on flammability.
Advice for firefighters
Protective equipment and precautions for firefighters:
In the event of fire, wear self-contained breathing apparatus.
Exposure to decomposition products may be a hazard to health.
Fire Fighting Instructions:
Collect contaminated fire extinguishing water separately. This must not be discharged into drains.
Fire residues and contaminated fire extinguishing water must be disposed of in accordance with local regulations.

Accidental release measures

Measured indicated is for substance at ~85% in mineral oil, as marketed

Personal precautions, protective equipment and emergency procedures
Personal precautions:
Advice for emergency responders
Ensure adequate ventilation.
Use personal protective equipment.

Material can create slippery conditions.
For personal protection see section 8.
Advice for non-emergency personnel
Avoid contact with spilled material. Do not touch or walk through spilled material.
Environmental precautions:
See attached ES
Prevent entry into waterways, sewers, basements or confined areas.
Local authorities should be advised if significant spillages cannot be contained.
Do not flush into surface water or sanitary sewer system.
Prevent further leakage or spillage if safe to do so.
Try to prevent the material from entering drains or water courses.
If the product contaminates rivers and lakes or drains inform respective authorities.

Methods and materials for containment and cleaning up
Methods for cleaning up:
Prevent further leakage or spillage if safe to do so.
Large Spills: Dyke far ahead of liquid spill for later recovery and disposal.
Recover by pumping or with suitable absorbent
Report spills as required to appropriate authorities.
Seek the advice of a specialist before using dispersants.
Dispose of according to local regulations.
In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations.
Material will sink to the sediment layer
Remove debris in path of spill prior to oiling and remove contaminated debris from shoreline and water surface.
Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust).
Keep in suitable, closed containers for disposal.
Clean contaminated floors and objects thoroughly while observing environmental regulations.

Handling and storage

Measured indicated is for substance at ~85% in mineral oil, as marketed

Precautions for safe handling
Do not breathe vapours or spray mist.
Avoid exposure - obtain special instructions before use.
Avoid contact with skin and eyes.
For personal protection see section 8.
May cause sensitisation of susceptible persons by skin contact.
Smoking, eating and drinking should be prohibited in the application area.
Dispose of rinse water in accordance with local and national regulations.
Normal measures for preventive fire protection.
Products may load from Infineum manufacturing site above the standard loading/unloading range.
Loading/unloading temperature:
50 °C (122 ° F) - 80 °C (176 ° F)
Viscosity @ Loading/unloading temperature:
129 cSt - 956 cSt
Static accumulator:
This material is not a static accumulator.

Conditions for safe storage, including any incompatibilities
Keep container tightly closed in a dry and well-ventilated place.
Containers which are opened must be carefully resealed and kept upright to prevent leakage.
Nitrogen blanketing is recommended
No decomposition if stored and applied as directed.
Storage temperature:
<= 80 °C (176 ° F)
Incompatible materials and coatings:
No data available

Transport information

Land transport (ADR/RID)

UN number:
Not regulated for transport by land
Shippingopen allclose all
Class:
Not regulated for transport by land
Classification code:
Not regulated for transport by land
Packaging group:
Not regulated for transport by land
Labels:
Not regulated for transport by land
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

UN number:
Not regulated for transport by sea under IMDG code
Proper shipping name and description:
Not regulated for transport by sea under IMDG code
Class:
Not regulated for transport by sea under IMDG code
Packaging group:
Not regulated for transport by sea under IMDG code
EmS code:
Not regulated for transport by sea under IMDG code
Labels:
Not regulated for transport by sea under IMDG code
Remarks
Not regulated for transport by sea under IMDG code

Air transport ICAO/IATA

UN number:
Not regulated for transport by air
Proper shipping name and description:
Not regulated for transport by air
Class:
Not regulated for transport by air
Packaging group:
Not regulated for transport by air
Labels:
Not regulated for transport by air
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Measured indicated is for substance at ~85% in mineral oil, as marketed

Control parameters
Exposure limits for materials that can be formed when handling this product: When mists/aerosols can occur, the following are recommended: 5mg/m³ - ACGIH TLV, 10 mg/m³ - ACGIH STEL
Limits/standards shown for guidance only. Follow applicable regulations.
Recommended monitoring procedures:
This product contains ingredients with exposure limits, personal, workplace atmosphere or biological monitoring may be required to determine the effectiveness of the ventilation or other control measures and/or the necessity to use respiratory protective equipment.
Reference should be made to European Standard EN 689 for methods for the assessment of exposure by inhalation to chemical agents and national guidance documents for methods for the determination of hazardous substances.
PNEC 1,1'-[iminobis(ethyleneiminoethylene)]bis[3-(octadecenyl)pyrrolidine-2,5-dione] : Value: 0.0476 mg/l
Exposure controls
Appropriate engineering controls:
See attached ES
No special requirements under ordinary conditions of use and with adequate ventilation.
Personal protective equipment
Respiratory protection:
The applicable European standard can be found in EN 140, EN 137, EN 143, EN 14387.
In the case of vapour formation use a respirator with an approved filter.
Hand protection
Remarks:
The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the standard EN 374 derived from it.
Polyvinyl alcohol or nitrile- butyl-rubber gloves Before removing gloves clean them with soap and water. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion, and the contact time. When handling

hot material, use heat resistant gloves.
Eye/face protection:
The applicable European standard can be found in EN 166.
Eye wash bottle with pure water
Tightly fitting safety goggles
Ensure that eyewash stations and safety showers are close to the workstation location.
Skin and body protection:
The applicable European standard can be found in EN 14605.
Impervious clothing
Choose body protection according to the amount and concentration of the dangerous substance at the work place.
Long sleeved clothing
Advice on general occupational hygiene
Hygiene measures:
Wash hands before breaks and immediately after handling the product.
Remove contaminated clothing and protective equipment before entering eating areas.
Environmental exposure controls
General advice:
See attached ES
Prevent entry into waterways, sewers, basements or confined areas.
Local authorities should be advised if significant spillages cannot be contained.
Do not flush into surface water or sanitary sewer system.
Prevent further leakage or spillage if safe to do so.
Try to prevent the material from entering drains or water courses.
If the product contaminates rivers and lakes or drains inform respective authorities.

Stability and reactivity

Measured indicated is for substance at ~85% in mineral oil, as marketed

Reactivity
No dangerous reaction known under conditions of normal use.
Chemical stability
Stable under recommended storage conditions.
Possibility of hazardous reactions
Hazardous reactions:
No hazards to be specially mentioned.

Conditions to avoid:
Excessive heat.

Incompatible materials:
Strong oxidizing agents

Hazardous decomposition products:
No decomposition if used as directed.

Disposal considerations

Measured indicated is for substance at ~85% in mineral oil, as marketed

Waste treatment methods
Product:
The product should not be allowed to enter drains, water courses or the soil.
Do not contaminate ponds, waterways or ditches with chemical or used container.
Dispose of contents/ container to an approved waste disposal plant.
Disposal recommendations based on material as supplied, Disposal must be in accordance with

applicable laws and regulations, and material characteristics at time of disposal
For the safety of persons conducting disposal, recycling or reclamation activities, refer to the information in Section 8, Exposure control and personal protection.
Empty containers.
Empty Container Warning (where applicable): Empty containers may contain residue and can be dangerous. Do not attempt to refill or clean containers without proper instructions. Empty drums should be completely drained and safely stored until appropriately reconditioned or disposed. Empty containers should be taken for recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance with governmental regulations. DO NOT PRESSURISE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION. THEY MAY EXPLODE AND CAUSE INJURY OR DEATH.
Regulatory disposal information
European Waste Code:
13 02 XX
waste engine, gear and lubricating oils