Registration Dossier

Administrative data

First-aid measures

After inhalation: fresh air.

After skin contact: wash off with plenty of water. Remove contaminated clothing.

After eye contact: rinse out with plenty of water. Immediately call in ophthalmologist.

After swallowing: immediately make victim drink water (two glasses at most). Consult a physician.

Fire-fighting measures

Suitable extinguishing media
Water, Carbon dioxide (CO2), Foam, Dry powder

Specific hazards during fire fighting
Combustible material, Development of hazardous combustion gases or vapours possible in the event of fire.

Special protective equipment for fire-fighters
Do not stay in dangerous zone without self-contained breathing apparatus. In order to avoid contact with skin, keep a safety distance and wear suitable protective clothing.

Further information
Prevent fire extinguishing water from contaminating surface water or the ground water system.

Accidental release measures

Personal precautions
Advice for non-emergency personnel: Avoid inhalation of dusts. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.

Environmental precautions
Do not empty into drains.

Methods for cleaning up
Cover drains. Collect, bind, and pump off spills.Take up dry. Dispose of properly. Clean up affected area. Avoid generation of dusts.

Handling and storage

Advice on safe handling
Observe label precautions.

Storage

Further information on storage conditions
Tightly closed. Dry.
This substance is handled under Strictly Controlled Conditions in accordance with REACH regulation Article 17(3) for on-site isolated intermediates and, in case the substance is transported to other sites for further processing, the substance should be handled at these sites under the Strictly Controlled Conditions as specified in REACH regulation Article 18(4). Site documentation to support safe handling arrangements including the selection of engineering, administrative and personal protective equipment controls in accordance with risk-based management systems is available at each Manufacturing and Use site.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all

Air transport ICAO/IATA

Remarks
Not subject to transport regulations. Use traffic-law compliant steel drums with a clamping ring and a solvent-resistant lacquered inner surface appropriate for packing group II also in the case of in-house transportation. Labelling according to national regulations. Secure against falling.
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Personal protective equipment
Protective clothing should be selected specifically for the working place, depending on concentration and quantity of the hazardous substances handled. The resistance of the protective clothing to chemicals should be ascertained with the respective supplier.

Respiratory protection
required when dusts are generated.
Recommended Filter type: Filter P 1 (acc. to DIN 3181) for solid particles of inert substances

Hand protectionfull contact:
Glove material: nitrile rubber
Glove thickness: 0,7 mm
Break through time: > 480 min
splash contact:
Glove material: nitrile rubber
Glove thickness: 0,7 mm
Break through time: > 480 min

The protective gloves to be used must comply with the specifications of EC Directive 89/686/EEC and the resultant standard EN374.


Eye protection
Safety glasses

Hygiene measures
Immediately change contaminated clothing. Apply skin- protective barrier cream. Wash hands and face after working with substance.

This substance is handled under Strictly Controlled Conditions in accordance with REACH regulation Article 17(3) for on-site isolated intermediates and, in case the substance is transported to other sites for further processing, the substance should be handled at these sites under the Strictly Controlled Conditions as specified in REACH regulation Article 18(4). Site documentation to support safe handling arrangements including the selection of engineering, administrative and personal protective equipment controls in accordance with risk-based management systems is available at each Manufacturing and Use site.

Stability and reactivity

Conditions to avoid
no information available

Materials to avoid
no information available

Hazardous decomposition products
no information available

Disposal considerations

Chemicals must be disposed of in compliance with the respective national regulations.