Registration Dossier

Administrative data

First-aid measures

Description of first aid measures
Immediately remove contaminated clothing. If the patient is likely to become unconscious, place and transport in stable sideways position (recovery position). First aid personnel should pay attention to their own safety.
If inhaled:
If difficulties occur after vapour/aerosol has been inhaled, remove to fresh air and seek medical attention.
On skin contact:
Immediately wash thoroughly with soap and water, seek medical attention.
On contact with eyes:
Immediately wash affected eyes for at least 15 minutes under running water with eyelids held open, consult an eye specialist.
On ingestion:
Rinse mouth immediately and then drink plenty of water, seek medical attention.

Indication of any immediate medical attention and special treatment needed
Treatment: Treat according to symptoms (decontamination, vital functions), no known specific antidote.

Fire-fighting measures

Extinguishing media
Suitable extinguishing media:
water spray, dry powder, foam
Unsuitable extinguishing media for safety reasons:
water jet
5.2. Special hazards arising from the substance or mixture
carbon oxides, nitrous gases, toxic gases/vapours
Evolution of fumes/fog. The substances/groups of substances mentioned can be released in case of fire.
5.3. Advice for fire-fighters
Special protective equipment:
Wear a self-contained breathing apparatus.
Further information:
The degree of risk is governed by the burning substance and the fire conditions. Contaminated extinguishing water must be disposed of in accordance with official regulations.

Accidental release measures

Personal precautions, protective equipment and emergency procedures
Use personal protective clothing. Breathing protection required.

Environmental precautions
Contain contaminated water/firefighting water. Do not discharge into drains/surface waters/groundwater.

Methods and material for containment and cleaning up
For large amounts: Pump off product.
For residues: Pick up with suitable absorbent material. Dispose of absorbed material in accordance with regulations.

Handling and storage

Precautions for safe handling
Wear suitable protective clothing and eye/face protection. When handling heated product, vapours of the product should be ventilated, and respiratory protection used.
Protection against fire and explosion:
Take precautionary measures against static discharges.

Conditions for safe storage, including any incompatibilities
Further information on storage conditions: Keep container tightly closed and dry; store in a cool place.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Control parameters
Components with occupational exposure limits
No occupational exposure limits known.

Exposure controls
Personal protective equipment
Respiratory protection:
Particle filter with high efficiency for solid and liquid particles (e.g. EN 143 or 149, Type P3 or FFP3).
Respiratory protection in case of vapour/aerosol release. Gas filter for gases/vapours of organic compounds (boiling point >65 °C, e. g. EN 14387 Type A)
Hand protection:
Chemical resistant protective gloves (EN 374)
Suitable materials also with prolonged, direct contact (Recommended: Protective index 6, corresponding > 480 minutes of permeation time according to EN 374):
fluoroelastomer (FKM) - 0.7 mm coating thickness
butyl rubber (butyl) - 0.7 mm coating thickness
polyvinylchloride (PVC) - 0.7 mm coating thickness
nitrile rubber (NBR) - 0.4 mm coating thickness
chloroprene rubber (CR) - 0.5 mm coating thickness
Suitable materials for short-term contact (recommended: At least protective index 2, corresponding > 30 minutes of permeation time according to EN 374)
natural rubber/natural latex (NR) - 0.5 mm coating thickness
Supplementary note: The specifications are based on tests, literature data and information of glove manufacturers or are derived from similar substances by analogy. Due to many conditions (e.g. temperature) it must be considered, that the practical usage of a chemical-protective glove in practice may be much shorter than the permeation time determined through testing.
Manufacturer's directions for use should be observed because of great diversity of types.
Eye protection:
Safety glasses with side-shields (frame goggles) (e.g. EN 166)
Body protection:
Body protection must be chosen based on level of activity and exposure., Protective suit, chemical-resistant apron and boots
General safety and hygiene measures
Handle in accordance with good industrial hygiene and safety practice. Wearing of closed work clothing is required additionally to the stated personal protection equipment. Handle in accordance with good industrial hygiene and safety practice.

Stability and reactivity

Reactivity
No hazardous reactions if stored and handled as prescribed/indicated.
Corrosion to metals:
No corrosive effect on metal.
Reactions with water/air:
Reaction with:
water
Flammable gases:
no
Toxic gases:
no
Corrosive gases:
no
Smoke or fog:
no
Peroxides:
no
Reaction with:
air
Flammable gases:
no
Toxic gases:
no
Corrosive gases:
no
Smoke or fog:
no
Peroxides:
no
Formation of flammable gases:
Remarks:
Forms no flammable gases in the presence of water.

Chemical stability
The product is stable if stored and handled as prescribed/indicated.
Peroxides:
0.000 %
The product does not contain peroxides.

Possibility of hazardous reactions
No hazardous reactions when stored and handled according to instructions.

Conditions to avoid
Avoid all sources of ignition: heat, sparks, open flame. Avoid electro-static discharge. Avoid heat.

Incompatible materials
Substances to avoid:
strong acids, strong bases, strong oxidizing agents

Hazardous decomposition products
Hazardous decomposition products:
carbon oxides, nitrous gases, toxic gases/vapours

Disposal considerations

Waste treatment methods
Must be disposed of or incinerated in accordance with local regulations.
Contaminated packaging:
Uncontaminated packaging can be re-used.
Packs that cannot be cleaned should be disposed of in the same manner as the contents.