Registration Dossier

Administrative data

First-aid measures

- 4.1 Description of first aid measures
- General information Instantly remove any clothing soiled by the product.
- After inhalation Supply fresh air or oxygen; call for doctor.
- After skin contact Instantly wash with water and soap and rinse thoroughly.
- After eye contact Rinse opened eye for several minutes (10 - 15)under running water.
- After swallowing
Instantly call for doctor.
Induce vomiting, only if person affected is fully conscious.
Rinse out mouth and then drink plenty of water (200 - 300 ml).
- 4.2 Most important symptoms and effects, both acute and delayed No further relevant information available.
- 4.3 Indication of any immediate medical attention and special treatment needed
No specific antidote available. Treat symptomatically and supportively.

Fire-fighting measures

- 5.1 Extinguishing media
- Suitable extinguishing agents: CO2, sand, extinguishing powder. Do not use water.
- For safety reasons unsuitable extinguishing agents Do not use a heavy water stream.
- 5.2 Special hazards arising from the substance or mixture
Can be released in case of fire
Nitrogen oxides (NOx)
Hydrogen chloride (HCl)
- 5.3 Advice for firefighters
- Protective equipment:
Wear self-contained breathing apparatus.
Do not inhale explosion gases or combustion gases.
Wear full protective suit.
- Additional information
Dispose of fire debris and contaminated fire fighting water in accordance with official regulations.

Accidental release measures

- 6.1 Personal precautions, protective equipment and emergency procedures
Ensure adequate ventilation
Avoid causing dust.
Do not inhale dust.
Wear protective clothing (described in section 8).
- 6.2 Environmental precautions: No special measures required.
- 6.3 Methods and material for containment and cleaning up:
Collect mechanically.
Dispose of contaminated material as waste according to item 13.

Handling and storage

- 7.1 Precautions for safe handling
Ensure good ventilation/exhaustion at the workplace.
Prevent formation of dust.
- Information about protection against explosions and fires: Protect against electrostatic charges.
- 7.2 Conditions for safe storage, including any incompatibilities
- Storage
- Requirements to be met by storerooms and containers: No special requirements.
- Information about storage in one common storage facility: Not required.
- Further information about storage conditions:
Keep container tightly closed.
Store under dry conditions.
- Storage class VCI class 13
- 7.3 Specific end use(s) No further relevant information available.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

- 8.1 Control parameters
- Components with limit values that require monitoring at the workplace: Not required.
- DNELs (Derived no-effect level) No information available
- PNECs (predicted no effect concentration) No information available
- Additional information: The lists that were valid during the compilation were used as basis.
- 8.2 Exposure controls
- Personal protective equipment
- General protective and hygienic measures
The usual precautionary measures should be adhered to general rules for handling chemicals.
Keep away from foodstuffs, beverages and food.
Take off immediately all contaminated clothing
Wash hands during breaks and at the end of the work.
Avoid contact with the eyes and skin.
Do not inhale dust
- Breathing equipment: Use breathing protection only if dust is formed.
- Recommended filter device for short term use: Filter P1
- Protection of hands: Protective gloves (EN 374).
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the
degradation
- Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality
and varies from manufacturer to manufacturer.
Nitrile rubber, NBR
Thickness of the material: 0.11 mm
Penetration time: > 480 min.
- Penetration time of glove material
The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be
observed.
- Eye protection: Tightly sealed safety glasses.
- Body protection: Protective work clothing.

Stability and reactivity

- 10.1 Reactivity No further relevant information available.
- 10.2 Chemical stability
- Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.
- 10.3 Possibility of hazardous reactions No dangerous reactions known
- 10.4 Conditions to avoid No further relevant information available.
- 10.5 Incompatible materials:
Strong oxidizing materials
Acids
Acid chlorides
Anhydrides
- 10.6 Hazardous decomposition products: No dangerous decomposition products known

Disposal considerations

- 13.1 Waste treatment methods
- Recommendation
After prior treatment product has to be disposed of in an incinerator for hazardous waste under adherence to
the regulations pertaining to the disposal of particularly hazardous waste.
- Uncleaned packagings:
- Recommendation:
Disposal must be made according to official regulations.
Packaging must be disposed of in compliance with country-specific regulations or must be passed to a
packaging return system.
Empty contaminated packagings thoroughly. They can be recycled after thorough and proper cleaning.
Packagings that cannot be cleaned are to be disposed of in the same manner as the product.
15 01 10: packaging containing residues of or contaminated by dangerous substances