Registration Dossier

Administrative data

First-aid measures

4.1 Description of first aid measures
General advice:Show this safety data sheet to the doctor in attendance.
If inhaled:If breathed in, move person into fresh air.
If symptoms persist, call a physician.
In case of skin contact:Take off contaminated clothing and shoes immediately.
Wash off immediately with plenty of water.
Call a physician immediately.
Wash contaminated clothing before reuse.
In case of eye contact :Rinse immediately with plenty of water, also under the eyelids, for at least 5 minutes.
Remove contact lenses.
If eye irritation persists, consult a specialist.
If swallowed:If swallowed, rinse mouth with water (only if the person is con-scious).
Call a physician immediately.
4.2 Most important symptoms and effects, both acute and delayed
Symptoms:Sensitisation
4.3 Indication of any immediate medical attention and special treatment needed
Treatment:Treat symptomatically.

Fire-fighting measures

5.1 Extinguishing media
Suitable extinguishing media :Water mist
Dry powder
Foam
Carbon dioxide (CO2)
Sand
Aqueous film forming foam (AFFF).
Use extinguishing measures that are appropriate to local cir-cumstances and the surrounding environment.
Unsuitable extinguishing media:Water spray jet
5.2 Special hazards arising from the substance or mixture
Specific hazards during fire-fighting:Risk of dust explosion.
Hazardous combustion products:Nitrogen oxides (NOx)
Carbon oxides
5.3 Advice for firefighters
Special protective equipment for firefighters :In the event of fire, wear self-contained breathing apparatus.
Further information:In the event of fire, cool tanks with water spray.
Avoid dust formation.

Accidental release measures

6.1 Personal precautions, protective equipment and emergency procedures
Personal precautions:Avoid dust formation.
Avoid breathing dust.
Evacuate personnel to safe areas.
Keep away from open flames, hot surfaces and sources of ignition.
6.2 Environmental precautions
Environmental precautions:Should not be released into the environment.
6.3 Methods and material for containment and cleaning up
Methods for cleaning up:Large spills: Sweep up or vacuum with HEPA filter or via wet cleaning into suitable containers for disposal.
Pick up and arrange without creating dust. Keep in properly labelled containers.
Small spills: Moisten a towel, cover the spill, pick up the spill or use HEPA vacuum.
Large spills + Small spills: Keep in suitable, closed containers for disposal. Treat recovered material as described in the sec-tion "Disposal considerations".
6.4 Reference to other sections
Refer to protective measures listed in sections 7 and 8., For disposal considerations see section 13.

Handling and storage

7.1 Precautions for safe handling
Advice on safe handling:Ensure all equipment is electrically grounded before beginning transfer operations.
To avoid thermal decomposition, do not overheat.
Use personal protective equipment as required.
Keep away from heat and sources of ignition.
Avoid inhalation, ingestion and contact with skin and eyes.
Avoid formation of dust and aerosols.
Advice on protection against:Avoid dust formation.
fire and explosion
Hygiene measures:Handle in accordance with good industrial hygiene and safety practice.
7.2 Conditions for safe storage, including any incompatibilities
Requirements for storage areas and containers:To maintain product quality, do not store in heat or direct sun-light. Store in original container. Keep containers tightly closed in a cool, well-ventilated place. Store at room temperature.
Recommended storage temperature:15 - 25 °C
7.3 Specific end use(s)
Specific use(s):Consult the technical guidelines for the use of this sub-stance/mixture.

Transport information

Land transport (ADR/RID)

UN number:
Not regulated as a dangerous good
Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Engineering measures
All personal protective equipment should be based on a risk assessment. Consult a Environment Health Safety expert if necessary.
Engineering controls should be used as the primary means to control possible exposures. Use process enclosures, local exhaust ventilation or other engineering controls to keep exposure levels below recommended exposure limits.
Personal protective equipment
Eye protection:Tightly fitting safety goggles
Hand protection Material:Nitrile rubber
Remarks:Take note of the information given by the producer concerning permeability and break through times, and of special workplace conditions (mechanical strain, duration of contact). Impervious gloves
Skin and body protection: closed work clothing
disposable one-piece overall
Respiratory protection: Engineering controls should always be the primary method of controlling exposures.
If respiratory protective equipment is needed for certain activities, the type as well as the corresponding protection factor will depend upon the risk assessment and air concentrations, hazards, physical and warning properties of substances present.
Use only respiratory protection that conforms to international/ national standards.
Suitable mask with particle filter P3
Protective measures:The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace.

Stability and reactivity

10.1 Reactivity
None reasonably foreseeable.
10.2 Chemical stability
Stable under recommended storage conditions.
10.3 Possibility of hazardous reactions
Hazardous reactions:Risk of dust explosion.
10.4 Conditions to avoid
Conditions to avoid:To avoid thermal decomposition, do not overheat.
Heat, flames and sparks.
10.5 Incompatible materials
Materials to avoid: Strong oxidizing agents
10.6 Hazardous decomposition products
Nitrogen oxides (NOx), Carbon oxides, Chlorocarbons

Disposal considerations

13.1 Waste treatment methods
Product:In accordance with National, Federal, State and Local regulations.
Must be incinerated in a suitable incineration plant holding a permit delivered by the competent authorities.
Contaminated packaging: Empty containers should be taken to an approved waste handling site for recycling or disposal.