Registration Dossier

Administrative data

First-aid measures

If inhaled:
If breathed in, move person into fresh air.
If symptoms persist, call a physician.

In case of skin contact:
Take off contaminated clothing and shoes immediately.
Wash off immediately with plenty of water.
Call a physician immediately.
Wash contaminated clothing before reuse.

In case of eye contact:
Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes.
Remove contact lenses.
Consult a physician.

If swallowed:
Rinse mouth with water.
Call a physician immediately.

Fire-fighting measures

Suitable extinguishing media:
water mist, dry powder, foam, carbon dioxide CO2, sand, Aqueous film forming foam (AFFF)

Unsuitable extinguishing media: Water spray jet

Special protective equipment for firefighters:
In the event of fire, wear self-contained breathing apparatus. Firefighters must wear fire resistant personal protective equipment.

Specific extinguishing methods: In the event of fire, cool tanks with water spray.

Accidental release measures

Personal precautions:
Evacuate personnel to safe areas.
Ensure adequate ventilation.
Keep away from open flames, hot surfaces and sources of ignition.

Environmental precautions:
Should not be released into the environment

Methods and material for containment and cleaning up:
Keep in properly labelled containers.
Keep in suitable, closed containers for disposal.
Treat recovered material as described in the section "Disposal considerations".
Dam up.
Soak up with inert absorbent material and dispose of as hazardous waste.

Handling and storage

Advice on safe handling:
To avoid thermal decomposition, do not overheat.
Use personal protective equipment as required.

Advice on protection against fire and explosion: Keep away from heat and sources of ignition.
Hygiene measures: Handle in accordance with good industrial hygiene and safety practice.

Requirements for storage areas and containers: Keep containers tightly closed in a cool, well-ventilated place.

Storage temperature: 15 - 25 °C.

Transport information

Land transport (ADR/RID)

UN number:
Not dangerous goods
Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (ADN(R))

UN number:
Not dangerous goods
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

UN number:
Not dangerous goods
Remarksopen allclose all

Air transport ICAO/IATA

UN number:
Not dangerous goods
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Engineering measures
Engineering controls should be used as the primary means to control possible exposures. Use process enclosures, local exhaust ventilation or other engineering controls to keep exposure levels below recommended exposure limits.

Personal protective equipment
Eye protection: Respirator with a full face mask
Hand protection: Nitrile rubber. Remark: Impervious gloves Take note of the information given by the producer concerning permeability and break through times, and of special workplace conditions (mechanical strain, duration of contact).
Skin and body protection: closed work clothing, long sleeved clothing

Respiratory protection:
Engineering controls should always be the primary method of controlling exposures.
If respiratory protective equipment is needed for certain activities, the type as well as the corresponding protection factor will depend upon the risk assessment and air concentrations, hazards, physical and warning properties of substances pre-sent.
Use only respiratory protection that conforms to international/ national standards.
Respirator with a full face mask
Filter type: ABEK-filter

Protective measures: The type of protective equipment must be selected according to the concentration and amount of the dangerous substance at the specific workplace.

Stability and reactivity

Reactivity: None reasonable foreseeable.

Chemical stability: Stable under recommended storage conditions.

Possibility of hazardous reactions: None known.

Conditions to avoid: To avoid thermal decomposition, do not overheat. Heat, flames and sparks.

Incompatible materials: Oxidizing agents

Hazardous decomposition products: fluoro, Carbon oxides

Disposal considerations

Must be incinerated in a suitable incineration plant holding a permit delivered by the competent authorities.
In accordance with local and national regulations.