Registration Dossier

Administrative data

First-aid measures

General advice : When symptoms persist or in all cases of doubt seek medical advice.
Inhalation : Move to fresh air. Oxygen or artificial respiration if needed. Symptoms may be delayed. Call a physician immediately.
Skin contact : Wash off immediately with soap and plenty of water. Wash contaminated clothing before re-use.
Eye contact : Rinse immediately with plenty of water for at least 15 minutes. Seek medical advice.
Ingestion : Call a physician or poison control centre immediately. If swallowed, DO NOT induce vomiting unless directed to do so by medical
personnel. Never give anything by mouth to an unconscious person.

Most important symptoms and effects, both acute and delayed

Symptoms: Inhalation may provoke the following symptoms:, Irritation, Shortness of breath, Lung oedema, Cough
Eye contact may provoke the following symptoms:, Lachrymation, Redness, Discomfort

Fire-fighting measures

Suitable extinguishing media : Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
Specific hazards during fire fighting: Hazardous decomposition products formed under fire conditions. Hazardous combustion products: Hydrogen fluoride.
Special protective equipment for fire-fighters : Wear self contained breathing apparatus for fire fighting if necessary.
Further information: Evacuate personnel to safe areas. Cool containers / tanks with water spray. Do not allow run-off from fire fighting to enter
drains or water courses.

Accidental release measures

Personal precautions : Evacuate personnel to safe areas. Wear personal protective equipment. Ventilate the area.
Environmental precautions : Do not discharge to streams, ponds, lakes or sewers. Avoid subsoil penetration.
Methods for cleaning up : Dam up. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Pick up and
transfer to properly labelled containers.

Handling and storage

Precautions for safe handling

Advice on safe handling: Do not use this product in consumer spray applications except in water-based coatings where the maximum concentration of active ingredient does not exceed 0.1 wt percent. Do not generate respirable particles unless suitable ventilation or respirator are used. Do not breathe vapours or spray mist. Avoid contact with skin, eyes and clothing.

Advice on protection against fire and explosion: To avoid thermal decomposition, do not overheat. Thermal decomposition can lead to release of irritating gases and vapours.

Conditions for safe storage, including any incompatibilities

Requirements for storage areas and containers: Keep containers tightly closed in a dry, cool and well-ventilated place. Store in accordance with the particular national regulations.

Other data: Perishable if frozen. Protect from freezing.


Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Engineering measures
Do not generate respirable particles unless suitable ventilation or respirator are used. Use an airless flow type of spray applicator. Keep spraying
pressure below 4.1 bar (410 kPa). Use only in area provided with appropriate exhaust ventilation. Use appropriate workplace ventilation to remove fumes that may be released on heating.

Personal protective equipment

Eye Protection: Wear safety glasses or coverall chemical splash goggles.
Eye protection complying with EN 166.

Hand protection:

Material: Protective gloves complying with EN 374.

Material: Latex gloves
Break through time: 480 min
Glove thickness: 0,95 mm

Material: butyl-rubber
Break through time: 480 min
Glove thickness: 0.89 mm

The break through time depends amongst other things on the material, the thickness and the type of glove and therefore has to be measured for each case. The suitability for a specific workplace should be discussed with the producers of the protective gloves. Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves. Also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion, and the contact time. Take note of the information given by the producer concerning permeability and break through times, and of special workplace conditions (mechanical strain, duration of contact). The choice of an appropriate glove does not only depend on its material but also on other quality features and is different from one producer to the other.

Skin and body protection: Lightweight protective clothing

Hygiene measures: Wash hands before breaks and immediately after handling the product. Wash contaminated clothing before re-use.

Respiratory protection: In case of mist, spray or aerosol exposure wear suitable personal respiratory protection and protective suit. Half mask with a particle filter P2 (EN 143). Consult the respirator manufacturer to determine the appropriate type of equipment for a given application. Observe respirator use limitations specified by the manufacturer.

Stability and reactivity

Reactivity: Stable under recommended storage conditions.

Chemical stability: Stable under normal conditions.

Possibility of hazardous reactions: Stable under normal conditions.

Conditions to avoid: To avoid thermal decomposition, do not overheat.

Incompatible materials: no data available

Hazardous decomposition products: Incompletely burned carbon products
Hydrofluoric acid...%
Carbon dioxide
Carbon monoxide
Other hazardous decomposition products may be formed.

Disposal considerations

Dispose of as hazardous waste in accordance with local and national regulations. Contaminated packaging – if recycling is not practicable, dispose of in compliance with local regulations