phenyl pent-4-enoate

Vapour pressure

Link to relevant study record(s)

Reference

Endpoint:

vapour pressure

Type of information:

experimental study

Adequacy of study:

key study

Study period:

2016

Reliability:

1 (reliable without restriction)

Rationale for reliability incl. deficiencies:

other: Guideline study performed under GLP. All relevant validity criteria were met.

Qualifier:

according to guideline

Guideline:

EU Method A.4 (Vapour Pressure)

Deviations:

no

Qualifier:

according to guideline

Guideline:

OECD Guideline 104 (Vapour Pressure Curve)

Deviations:

no

GLP compliance:

yes (incl. QA statement)

Remarks:

inspected: June 2015; signature: September 2015

Type of method:

gas saturation method

Temp.:

25 °C

Vapour pressure:

3.17 Pa

Calculation of the Vapour Pressure

The vapour pressure at a given temperature can be calculated by determining the amount of material transported by a known amount of carrier gas. Volume correction was completed by appropriate calculation methods described in the study report. The Vapour pressure was subsequently calculated from:

Pvp = W x R x T / V x M

Pvp = vapour pressure [Pa] (calculated)

W = mass of evaporated test item [micro-grams] (from analysis)

R = gas constant = 8.314 J/K mol

T = temperature [K] (measured)

V = volume of nitrogen at test temperature [mL] (determined from flow rate)

M = molar mass of test item

 

From experimental data performed at the three test temperatures, the vapour pressure of the test item at 25 °C was calculated by interpolation of ln vapour pressure versus the reciprocal of test temperature (K).

 

The mass of transferred test item and corresponding vapour pressures are shown in the following table:

Saturator Column.	Temp. [°C]	Volume* V [mL]	Mass of Test Item in Trap 1 [µg]	Mass of Test Item in Trap 2 [µg] #	Total Mass of Test Item [µg]	Vapor Pressure [Pa]	Average Vapor Pressure [Pa] (Std Dev)
A	15	37502	3321	0	3321	1.20	1.24   (3.47 x 10-2)
B		50003	4528	0	4528	1.23
C		62504	5853	0	5853	1.27
A	25	29471	6457	0	6457	3.08	3.15   (6.46 x 10-2)
B		39295	8860	0	8860	3.17
C		49119	11198	0	11198	3.21
A	5	121738	3977	0	3977	0.429	0.442   (1.73 x 10-2)
B		162318	5379	0	5379	0.435
C		202897	7132	0	7132	0.461

*: Corrected volume at test temperature as calculated under “Volume correction”

#: 0 µg refers to non-detected within trap 2

A, B and C refer to three different flow rates respectively, reported in the full study report.

 

The vapour pressure at 25 °C was interpolated from the vapour pressure curve (ln Pvp versus 1/T) and was calculated to 3.17 Pa.

The linearity of the detector response with respect to concentration was assessed over the concentration range of 66.4 to 224 mg/L. This was satisfactory with a correlation coefficient of 1.000 being obtained.

Conclusions:

The vapour pressure of the test substance has been determined to be 3.17 Pa at 25 °C.

Executive summary:

The vapour pressure was determined using EU Method A.4 and OECD TG 104 using the gas saturation method under GLP. To ensure saturation control, three different flow rates were used at each temperature. In the determination higher flow rates did not lead to lower vapour pressures, which means that the nitrogen was saturated with test substance under the conditions of the test. The mean vapour pressure was 5°C: 0.442 Pa;  15°C: 1.24 Pa and 25°C: 3.15 Pa respectively. The vapour pressure of the test substance was interpolated from the vapour pressure curve (ln Pvp versus 1/T) and was calculated to be 3.17 Pa at 25°C.

Description of key information

Vapour Pressure: 3.17 Pa at 25 °C, EU Method A.4 - Gas Saturation Method, 2017

Key value for chemical safety assessment

Vapour pressure:

3.17 Pa

at the temperature of:

25 °C

Additional information

Key study: EU Method A.4, 2017 : The vapour pressure was determined using EU Method A.4 and OECD TG 104 using the gas saturation method under GLP. To ensure saturation control, three different flow rates were used at each temperature. In the determination higher flow rates did not lead to lower vapour pressures, which means that the nitrogen was saturated with test substance under the conditions of the test. The mean vapour pressure was 5°C: 0.442 Pa;  15°C: 1.24 Pa and 25°C: 3.15 Pa respectively. The vapour pressure of the test substance was interpolated from the vapour pressure curve (ln Pvp versus 1/T) and was calculated to be 3.17 Pa at 25°C.