Registration Dossier

Administrative data

First-aid measures

Eye Contact: Flush with water while holding eyelids open for at least 15 minutes. Seek medical attention immediately.
Skin Contact: Remove contaminated clothing. Flush area with large amounts of water. Use soap. Seek medical attention.
Ingestion: Never give anything by mouth to an unconscious person. Wash out mouth with water. Do not induce vomiting unless directed by medical personnel. Seek medical attention immediately.
Inhalation: Remove to fresh air and keep patient at rest. Seek medical attention immediately.

Fire-fighting measures

Extinguishing Media: Extinguish fires with CO2, extinguishing powder, foam, or water.
Special Hazards Arising from the Substance or Mixturea: Hazardous Combustion Products: Formation of toxic gases is possible during heating or fire.
Fire / Explosion Hazards: Fine particles (such as dust and mists) may fuel fires/explosions.
Advice for Fire-Fighters During all fire fighting activities, wear appropriate protective equipment, including self-contained breathing apparatus.

Accidental release measures

Personal Precautions, Protective Equipment and Emergency Procedures
Personnel involved in clean-up should wear appropriate personal protective equipment (see Section 8). Minimize exposure.
Environmental Precautions: Place waste in an appropriately labeled, sealed container for disposal. Care should be taken to avoid environmental release.
Methods and Material for Containment and Cleaning Up
Measures for Cleaning /Collecting: Contain the source of spill if it is safe to do so. Collect spilled material by a method that controls dust generation. A damp cloth or a filtered vacuum should be used to clean spills of dry solids. Clean spill area thoroughly.
Additional Consideration for Large Spills: Non-essential personnel should be evacuated from affected area. Report emergency situations immediately. Clean up operations should only be undertaken by trained personnel.

Handling and storage

Precautions for Safe Handling Ground and bond all bulk transfer equipment. Avoid open handling. Minimize dust generation. Use local exhaust ventilation or perform work under fume hood/fume cupboard. Avoid inhalation and contact with skin, eye, and clothing. When handling, use appropriate personal protective equipment (see Section 8). Wash hands and any exposed skin after removal of PPE. Releases to the environment should be avoided. Review and implement appropriate technical and procedural waste water and waste disposal measures to prevent occupational exposure or environmental releases. Potential points of process emissions of this material to the atmosphere should be controlled with dust collectors, HEPA filtration systems or other equivalent controls.
Conditions for Safe Storage, Including any Incompatibilities Storage Conditions: Store at room temperature in properly labeled containers. Keep away from heat, sparks and flames.
Specific end use(s): No data available

Transport information

Land transport (ADR/RID)

UN number:
Not regulated for transport.
Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (ADN(R))

UN number:
Not regulated for transport.
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

UN number:
Not regulated for transport.
Remarksopen allclose all

Air transport ICAO/IATA

UN number:
Not regulated for transport.
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Control Parameters: The purpose of the Occupational Exposure Band (OEB) classification system is to separate substances into different Hazard categories when the available data are sufficient to do so, but inadequate to establish an Occupational Exposure Limit (OEL). The OEB given is based upon an analysis of all currently available data; as such, this value may be subject to revision when new information becomes available.
Exposure Controls Engineering Controls: Engineering controls should be used as the primary means to control exposures. Use process containment, local exhaust ventilation, or other engineering controls to maintain airborne levels within the OEB range.
Personal Protective Equipment: Refer to applicable national standards and regulations in the selection and use of personal protective equipment (PPE).
Hands: Wear impervious gloves as minimum protection.
Eyes: Wear safety glasses as minimum protection.
Skin: Wear impervious protective clothing when handling this compound.
Respiratory protection: If airborne exposures are within or exceed the Occupational Exposure Band (OEB) range, wear an appropriate respirator with a protection factor sufficient to control exposures to the bottom of the OEB range.

Stability and reactivity

Reactivity: No data available
Chemical Stability: Stable under normal conditions of use.
Possibility of Hazardous Reactions Oxidizing Properties: No data available
Conditions to Avoid: Fine particles (such as dust and mists) may fuel fires/explosions.
Incompatible Materials: As a precautionary measure, keep away from strong oxidizers
Hazardous Decomposition Products: No data available

Disposal considerations

Waste Treatment Methods: Dispose of waste in accordance with all applicable laws and regulations. Member State
specific and Community specific provisions must be considered. Considering the relevant
known environmental and human health hazards of the material, review and implement
appropriate technical and procedural waste water and waste disposal measures to prevent
occupational exposure and environmental release. It is recommended that waste minimization
be practiced. The best available technology should be utilized to prevent environmental
releases. This may include destructive techniques for waste and wastewater.