Registration Dossier
Registration Dossier
Please be aware that this old REACH registration data factsheet is no longer maintained; it remains frozen as of 19th May 2023.
The new ECHA CHEM database has been released by ECHA, and it now contains all REACH registration data. There are more details on the transition of ECHA's published data to ECHA CHEM here.
Use of this information is subject to copyright laws and may require the permission of the owner of the information, as described in the ECHA Legal Notice.
EC number: 237-731-1 | CAS number: 13951-70-7
Guidance on Safe Use
Guidance on Safe Use
Currently viewing:
Administrative data
First-aid measures
INHALATION: Remove to fresh air. If any trouble breathing, get immediate medical attention. Administer artificial respiration if breathing has ceased. If irritation or symptoms occur or persist, consult a physician.
SKIN CONTACT: In case of skin contact, while wearing protective gloves, carefully remove any contaminated clothing, including shoes, and wash skin thoroughly with soap and water. If irritation or symptoms occur or persist, consult a physician.
EYE CONTACT: In case of eye contact, immediately rinse eyes thoroughly with plenty of water. If wearing contact lenses,
remove only after initial rinse, and continue rinsing eyes for at least 15 minutes. If irritation occurs or persists, consult a physician.
INGESTION: Rinse mouth and drink a glass of water. Do not induce vomiting unless under the direction of a qualified medical professional or Poison Control Center. If symptoms persist, consult a physician.
FIRST AID RESPONDER PROTECTION: Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves with appropriate personal protective equipment. Induce artificial respiration with the aid of a pocket mask equipped with a one-way valve or other proper respiratory medical device. DO NOT use mouth-to-mouth method if victim ingested or inhaled the substance.
MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED The toxicological properties of this material have not been fully characterized in humans and animals. Therefore, laboratory or process control systems and appropriate work practices should be in place to minimize the potential for inhalation exposure, skin contact, eye contact, or ingestion when working with this material.
INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDED
NOTE TO PHYSICIAN: In cases of overexposure treat supportively and symtomatically.
SKIN CONTACT: In case of skin contact, while wearing protective gloves, carefully remove any contaminated clothing, including shoes, and wash skin thoroughly with soap and water. If irritation or symptoms occur or persist, consult a physician.
EYE CONTACT: In case of eye contact, immediately rinse eyes thoroughly with plenty of water. If wearing contact lenses,
remove only after initial rinse, and continue rinsing eyes for at least 15 minutes. If irritation occurs or persists, consult a physician.
INGESTION: Rinse mouth and drink a glass of water. Do not induce vomiting unless under the direction of a qualified medical professional or Poison Control Center. If symptoms persist, consult a physician.
FIRST AID RESPONDER PROTECTION: Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves with appropriate personal protective equipment. Induce artificial respiration with the aid of a pocket mask equipped with a one-way valve or other proper respiratory medical device. DO NOT use mouth-to-mouth method if victim ingested or inhaled the substance.
MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED The toxicological properties of this material have not been fully characterized in humans and animals. Therefore, laboratory or process control systems and appropriate work practices should be in place to minimize the potential for inhalation exposure, skin contact, eye contact, or ingestion when working with this material.
INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDED
NOTE TO PHYSICIAN: In cases of overexposure treat supportively and symtomatically.
Fire-fighting measures
EXTINGUISHING MEDIA
SUITABLE EXTINGUISHING MEDIA: Carbon dioxide (CO2), extinguishing powder or water spray.
UNSUITABLE EXTINGUISHING MEDIA: None known.
SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE
EXPLOSION HAZARDS: Under normal conditions of use, this material does not present a significant fire or explosion hazard. However, like most organic compounds, this material may present a dust deflagration hazard if sufficient quantities are suspended in air. This hazard may exist where sufficient quantities of finely divided material are (or may become) suspended in air during typical process operations. An assessment of each operation should be conducted and suitable deflagration prevention and protection techniques employed. The sensitivity of this material to ignition by electrostatic discharges has not been determined. In the absence of testing data, all conductive plant items and operations personnel handling this material should be suitably grounded.
SPECIAL FIRE HAZARDS: None known.
ADVICE FOR FIREFIGHTERS
SPECIAL FIRE FIGHTING PROCEDURES: Wear full protective clothing and self-contained breathing apparatus (SCBA).
SUITABLE EXTINGUISHING MEDIA: Carbon dioxide (CO2), extinguishing powder or water spray.
UNSUITABLE EXTINGUISHING MEDIA: None known.
SPECIAL HAZARDS ARISING FROM THE SUBSTANCE OR MIXTURE
EXPLOSION HAZARDS: Under normal conditions of use, this material does not present a significant fire or explosion hazard. However, like most organic compounds, this material may present a dust deflagration hazard if sufficient quantities are suspended in air. This hazard may exist where sufficient quantities of finely divided material are (or may become) suspended in air during typical process operations. An assessment of each operation should be conducted and suitable deflagration prevention and protection techniques employed. The sensitivity of this material to ignition by electrostatic discharges has not been determined. In the absence of testing data, all conductive plant items and operations personnel handling this material should be suitably grounded.
SPECIAL FIRE HAZARDS: None known.
ADVICE FOR FIREFIGHTERS
SPECIAL FIRE FIGHTING PROCEDURES: Wear full protective clothing and self-contained breathing apparatus (SCBA).
Accidental release measures
PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND EMERGENCY PROCEDURES
PERSONAL PRECAUTIONS: Avoid generation of dust during clean-up. Wear appropriate personal protective equipment as specified in Section 8. Keep personnel away from the clean-up area.
METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP
SPILL RESPONSE / CLEANUP: All spills should be handled according to site requirements and based on precautions cited in the MSDS. In the case of liquids, use proper absorbent materials. For laboratories and small-scale operations, incidental spills within a hood or enclosure should be cleaned by using a HEPA filtered vacuum or wet cleaning methods as appropriate. For large dry or liquid spills or those spills outside enclosure or hood, appropriate emergency response personnel should be notified. In manufacturing and large-scale operations, HEPA vacuuming prior to wet mopping or cleaning is required.
PERSONAL PRECAUTIONS: Avoid generation of dust during clean-up. Wear appropriate personal protective equipment as specified in Section 8. Keep personnel away from the clean-up area.
METHODS AND MATERIAL FOR CONTAINMENT AND CLEANING UP
SPILL RESPONSE / CLEANUP: All spills should be handled according to site requirements and based on precautions cited in the MSDS. In the case of liquids, use proper absorbent materials. For laboratories and small-scale operations, incidental spills within a hood or enclosure should be cleaned by using a HEPA filtered vacuum or wet cleaning methods as appropriate. For large dry or liquid spills or those spills outside enclosure or hood, appropriate emergency response personnel should be notified. In manufacturing and large-scale operations, HEPA vacuuming prior to wet mopping or cleaning is required.
Handling and storage
PRECAUTIONS FOR SAFE HANDLING
HANDLING: Keep containers adequately sealed during material transfer, transport, or when not in use. Wash face, hands, and any exposed skin after handling. Do not eat, drink, or smoke when using this substance or mixture. Appropriate handling of this material is dependent on many factors, including physical form, duration and frequency of process or task, and effectiveness of engineering controls. Site-specific risk assessments should be conducted to determine the feasibility and the appropriateness of all exposure control measures. See Section 8 (Exposure Controls) for additional guidance.
CONDITIONS FOR SAFE STORAGE, INCLUDING ANY IMCOMPATIBILITIES
STORAGE: Store at 15-25 deg C. Store in adequately sealed container.
SPECIFIC END USE(S)
Refer to Section 1 for identified use(s).
HANDLING: Keep containers adequately sealed during material transfer, transport, or when not in use. Wash face, hands, and any exposed skin after handling. Do not eat, drink, or smoke when using this substance or mixture. Appropriate handling of this material is dependent on many factors, including physical form, duration and frequency of process or task, and effectiveness of engineering controls. Site-specific risk assessments should be conducted to determine the feasibility and the appropriateness of all exposure control measures. See Section 8 (Exposure Controls) for additional guidance.
CONDITIONS FOR SAFE STORAGE, INCLUDING ANY IMCOMPATIBILITIES
STORAGE: Store at 15-25 deg C. Store in adequately sealed container.
SPECIFIC END USE(S)
Refer to Section 1 for identified use(s).
Transport information
Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all
Marine transport (UN RTDG/IMDG)
Shippingopen allclose all
Remarksopen allclose all
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all
Exposure controls / personal protection
CONTROL PARAMETERS
OCCUPATIONAL EXPOSURE BAND (OEB): OEB 3: 10-100 mcg/m3. Materials in an OEB 3 category are considered moderate health hazards. The OEB is a range of airborne concentrations expressed as an 8-hour Time Weighted Average (8-hr. TWA) and is intended to be used with Industrial Hygiene Risk Assessment to assist with industrial hygiene sampling and selection of proper controls for worker protection. Consult your site safety and industrial hygiene staff for guidance on handling and control strategies.
EXPOSURE LIMIT VALUES: No exposure limits are available for this material.
EXPOSURE CONTROLS
The health hazard risks of handling this material are dependent on many factors, including physical form, duration and frequency of process or task, and effectiveness of engineering controls. Site-specific risk assessments should be conducted to determine the feasibility and the appropriateness of all exposure control measures. Exposure controls for normal operating or routine procedures follow a tiered strategy. Engineering controls are the
preferred means of long-term or permanent exposure control. If engineering controls are not feasible, appropriate use of personal protective equipment (PPE) may be considered as alternative control measures. Exposure controls for non-routine operations must be evaluated and addressed as part of the site-specific risk assessment.
RECOMMENDED PERSONAL PROTECTIVE EQUIPMENT (PPE):
Body Protection:
In small-scale or laboratory operations, lab coats or equivalent protection is required. Disposable Tyvek or other dust impermeable suit should be considered based on procedure or level of exposure. Use of additional PPE such as shoe coverings, gauntlets, hood, or head covering may be necessary. Consult your site safety staff for guidance.
Skin Protection:
In large-scale or manufacturing operations, disposable Tyvek or other dust impermeable suit is recommended and based on level of exposure. Use of additional PPE such as shoe coverings, gauntlets, hood, or head covering may be necessary. Consult your site safety staff for guidance. Gloves that provide an appropriate barrier to the skin are recommended if there is potential for contact with this material. Consult your site safety staff for guidance.
Respiratory Protection:
Respiratory protective equipment (RPE) may be required for certain laboratory and large-scale manufacturing tasks if potential airborne breathing zone concentrations of substances exceed the relevant exposure limit(s). Workplace risk assessment should be completed before specifying and implementing RPE usage. Potential exposure points and pathways, task duration and frequency, potential employee contact with the substance, and the ability of the substance to be rendered airborne during specific tasks should be evaluated. Initial and ongoing strategies of quantitative exposure measurement should be obtained as required by the workplace risk assessment. All RPE must conform to local and regional specifications for efficacy and performance. Consult your site or corporate health and safety professional for additional guidance.
Eye Protection:
Safety glasses with side shields. Use of goggles or full face protection may be required based on hazard, potential for contact, or level of exposure. Consult your site safety staff for guidance.
OCCUPATIONAL EXPOSURE BAND (OEB): OEB 3: 10-100 mcg/m3. Materials in an OEB 3 category are considered moderate health hazards. The OEB is a range of airborne concentrations expressed as an 8-hour Time Weighted Average (8-hr. TWA) and is intended to be used with Industrial Hygiene Risk Assessment to assist with industrial hygiene sampling and selection of proper controls for worker protection. Consult your site safety and industrial hygiene staff for guidance on handling and control strategies.
EXPOSURE LIMIT VALUES: No exposure limits are available for this material.
EXPOSURE CONTROLS
The health hazard risks of handling this material are dependent on many factors, including physical form, duration and frequency of process or task, and effectiveness of engineering controls. Site-specific risk assessments should be conducted to determine the feasibility and the appropriateness of all exposure control measures. Exposure controls for normal operating or routine procedures follow a tiered strategy. Engineering controls are the
preferred means of long-term or permanent exposure control. If engineering controls are not feasible, appropriate use of personal protective equipment (PPE) may be considered as alternative control measures. Exposure controls for non-routine operations must be evaluated and addressed as part of the site-specific risk assessment.
RECOMMENDED PERSONAL PROTECTIVE EQUIPMENT (PPE):
Body Protection:
In small-scale or laboratory operations, lab coats or equivalent protection is required. Disposable Tyvek or other dust impermeable suit should be considered based on procedure or level of exposure. Use of additional PPE such as shoe coverings, gauntlets, hood, or head covering may be necessary. Consult your site safety staff for guidance.
Skin Protection:
In large-scale or manufacturing operations, disposable Tyvek or other dust impermeable suit is recommended and based on level of exposure. Use of additional PPE such as shoe coverings, gauntlets, hood, or head covering may be necessary. Consult your site safety staff for guidance. Gloves that provide an appropriate barrier to the skin are recommended if there is potential for contact with this material. Consult your site safety staff for guidance.
Respiratory Protection:
Respiratory protective equipment (RPE) may be required for certain laboratory and large-scale manufacturing tasks if potential airborne breathing zone concentrations of substances exceed the relevant exposure limit(s). Workplace risk assessment should be completed before specifying and implementing RPE usage. Potential exposure points and pathways, task duration and frequency, potential employee contact with the substance, and the ability of the substance to be rendered airborne during specific tasks should be evaluated. Initial and ongoing strategies of quantitative exposure measurement should be obtained as required by the workplace risk assessment. All RPE must conform to local and regional specifications for efficacy and performance. Consult your site or corporate health and safety professional for additional guidance.
Eye Protection:
Safety glasses with side shields. Use of goggles or full face protection may be required based on hazard, potential for contact, or level of exposure. Consult your site safety staff for guidance.
Stability and reactivity
STABILITY/ REACTIVITY:
Stable under conditions specified in Section 7 of this SDS. No hazardous reactions known.
CONDITIONS AND MATERIALS TO AVOID:
None known.
HAZARDOUS DECOMPOSITION PRODUCTS / REACTIONS:
No dangerous decomposition is expected if used according to manufacturer's specifications.
Stable under conditions specified in Section 7 of this SDS. No hazardous reactions known.
CONDITIONS AND MATERIALS TO AVOID:
None known.
HAZARDOUS DECOMPOSITION PRODUCTS / REACTIONS:
No dangerous decomposition is expected if used according to manufacturer's specifications.
Disposal considerations
WASTE TREATMENT METHODS
MATERIAL WASTE:
Disposal must be in accordance with applicable federal, state/provincial, and/or local regulations. Incineration is the preferred method of disposal, whenappropriate. Operations that involve the crushing or shredding of waste materials or returned goods must be handled to meet the recommended
exposure limit(s).
PACKAGING AND CONTAINERS:
Disposal must be in accordance with applicable federal, state/provincial, and/or local regulations.
MATERIAL WASTE:
Disposal must be in accordance with applicable federal, state/provincial, and/or local regulations. Incineration is the preferred method of disposal, whenappropriate. Operations that involve the crushing or shredding of waste materials or returned goods must be handled to meet the recommended
exposure limit(s).
PACKAGING AND CONTAINERS:
Disposal must be in accordance with applicable federal, state/provincial, and/or local regulations.
Information on Registered Substances comes from registration dossiers which have been assigned a registration number. The assignment of a registration number does however not guarantee that the information in the dossier is correct or that the dossier is compliant with Regulation (EC) No 1907/2006 (the REACH Regulation). This information has not been reviewed or verified by the Agency or any other authority. The content is subject to change without prior notice.
Reproduction or further distribution of this information may be subject to copyright protection. Use of the information without obtaining the permission from the owner(s) of the respective information might violate the rights of the owner.
