Registration Dossier

Administrative data

First-aid measures

General information
Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves.

Description of first aid measures
Inhalation: Move to fresh air. Call a physician if symptoms develop or persist.
Skin contact: Remove contaminated clothing. Wash with plenty of soap and water. If skin irritation occurs: Get medical advice/attention. Wash contaminated clothing before reuse.
Eye contact: Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical attention immediately.
Ingetion: Rinse mouth. Get medical attention if symptoms occur.

Most important symptoms and effects, both acute and delayed
Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. Permanent eye damage including blindness could result. Skin irritation. May cause redness and pain.

Indication of any immediate medical attention and special treatment needed
Provide general supportive measures and treat symptomatically. Keep victim under observation. Symptoms may be delayed.

Fire-fighting measures

General fire hazards
No unusual fire or explosion hazards noted.

Extinguishing media
Suitable extinguishing media: Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).
Unsuitable extinguishing media: Do not use water jet as an extinguisher, as this will spread the fire.

Special hazards arising from the substance or mixture
During fire, gases hazardous to health may be formed.

Advice for firefighters
Special protective equipment for firefighters: Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Special fire fighting procedures: Move containers from fire area if you can do so without risk.

Specific methods
Use standard firefighting procedures and consider the hazards of other involved materials.

Accidental release measures

Personal precautions, protective equipment and emergency procedures
For non-emergency personnel:Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear appropriate protective equipment and clothing during clean-up. Do not breathe vapour. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ensure
adequate ventilation. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS.
For emergency responders: Keep unnecessary personnel away. Use personal protection recommended in Section 8 of the SDS.

Environmental precautions
Avoid discharge into drains, water courses or onto the ground.

Methods and material for containment and cleaning up
This product is miscible in water.
Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.
Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS.

Handling and storage

Precautions for safe handling
Do not breathe vapour. Do not get this material in contact with eyes. Avoid contact with eyes, skin, and clothing. Provide adequate ventilation. Wear appropriate personal protective equipment. Observe good industrial hygiene practices.

Conditions for safe storage, including any incompatibilities
Store in tightly closed container. Store away from incompatible materials (see Section 10 of the SDS).

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Appropriate engineering controls
Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Provide eyewash station and safety shower.

Individual protection measures, such as personal protective equipment
General information: Use personal protective equipment as required. Personal protection equipment should be chosen according to the CEN standards and in discussion with the supplier of the personal protective equipment.
Eye/face protection: Wear safety glasses with side shields (or goggles) and a face shield.
Skin protection
- Hand protection Wear appropriate chemical resistant gloves.
- Other Wear appropriate chemical resistant clothing.
Respiratory protection: In case of insufficient ventilation, wear suitable respiratory equipment.
Thermal hazards: Wear appropriate thermal protective clothing, when necessary.

Hygiene measures
Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants.

Environmental exposure controls
Environmental manager must be informed of all major releases.

Stability and reactivity

Reactivity
The product is stable and non-reactive under normal conditions of use, storage and transport.

Chemical stability
Material is stable under normal conditions.

Possibility of hazardous reactions
No dangerous reaction known under conditions of normal use.

Conditions to avoid
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Contact with incompatible materials

Incompatible materials
Strong oxidising agents.

Hazardousc decomposition products
No hazardous decomposition products are known.

Disposal considerations

Waste treatment methods
Residual waste: Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions).
Contaminated packaging: Since emptied containers may retain product residue, follow label warnings even after container is emptied. Empty containers should be taken to an approved waste handling site for recycling or disposal.
EU waste code: The Waste code should be assigned in discussion between the user, the producer and the waste disposal company.
Disposal methods/information: Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Dispose of contents/container in accordance with local/regional/national/international regulations.
Special precautions: Dispose in accordance with all applicable regulations.