Registration Dossier

Administrative data

First-aid measures

Eye contact
Flush eyes thoroughly with a large amount of water and consult a physician.

Skin contact
Wash off with water. Consult a physician if irritation persists.

Inhalation
Move subject to fresh air and keep him calm. In case of complaints get medical advice.

Ingestion
In case of complaints get medical advice.

General advice
Remove contaminated, soaked clothing.

Fire-fighting measures

Suitable extinguishing media
none required

Accidental release measures

Personal precautions
Take care for adequate ventilation. Use personal protective clothing. Use breathing apparatus if exposed to vapours/dust/mist/aerosol.

Environmental precautions
Prevent product from getting into drains/surface water/groundwater.

Methods for cleaning up
Larger quantities: Take up mechanically (by pumping). Smaller quantities and/or residues: Contain with absorbent material (e.g. sand, diatomaceous earth, acid absorbent, universal absorbent or sawdust). Dispose of in accordance with regulations.

Handling and storage

Safe handling advice
Keep container tightly closed.

Advice on protection against fire and explosion
No special measures required.

Requirements for storage areas and containers
Protect from light. Keep only in the original container at a temperature not exceeding 30 °C. Fill the container by approximately 90 % only as oxygen (air) is required for stabilisation. With large storage containers make sure the oxygen (air) supply is sufficient to ensure stability.

Transport information

Land transport (ADR/RID)

Shippingopen allclose all
Remarks:
Not a dangerous good within the meaning of transportation regulations.

Inland waterway transport (ADN(R))

Shippingopen allclose all
Remarks
Not a dangerous good within the meaning of transportation regulations.

Marine transport (IMDG)

Remarks
Not a dangerous good within the meaning of transportation regulations.

Air transport ICAO/IATA

Remarks
Not a dangerous good within the meaning of transportation regulations.
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Exposure controls
For monitoring procedures refer to for instance "Empfohlene Analysenverfahren für Arbeitsplatzmessungen", Schriftenreihe der Bundesanstalt für Arbeitsschutz and "NIOSH Manual of Analytical Methods", National Institute for Occupational Safety and Health

Protective measures
Avoid contact with eyes and skin.

Hygiene measures
Store work clothing separately. Remove soiled or soaked clothing immediately. Follow the usual good standards of occupational hygiene. Clean skin thoroughly after work; apply skin cream.

Respiratory protection
Breathing apparatus in the case of aerosol or mist formation, short term: filter appliance, filter P2

Hand protection
natural rubber gloves (0.6 mm), Break through time 120 min (EN 374)
In practice, due to variable exposure conditions, this information can only be an aid to orientation for the selection of a suitable chemical protection glove. In particular, this information does not substitute suitability tests by the end user.

General information
Gloves should be replaced regularly, especially after extended contact with the product. For each work-place a suitable glove type has to be selected.

Eye protection
tightly fitting goggles

Stability and reactivity

Conditions to avoid
This material is considered stable under specified conditions of storage, shipment and/or use.

Materials to avoid
strong oxidizing agents
Free radical initiators.

Hazardous decomposition products
None when used as directed.

Thermal decomposition
No decomposition when used as directed.

Hazardous reactions
Polymerization with heat evolution may occur in the presence of radical forming substances (e.g. peroxides), reducing substances, and/or heavy metal ions.

Disposal considerations

Product
Waste is hazardous. It must be disposed of in accordance with the regulations after consultation of the competent local authorities and the disposal company in a suitable and licensed facility.

Uncleaned packaging
Contaminated packaging should be emptied optimally and after appropriate professional cleansing may be taken for reuse. Packaging that cannot be cleaned should be disposed of professionally. Uncontaminated packaging may be taken for recycling.

Code of waste
EWC 07 02 08
waste from the manufacture, formulation, supply and use (MFSU) of plastics, synthetic rubber and man-made fibres - other still bottoms and reaction residues Always check the given waste codes according to the actual conditions of manufacturing, formulation or use in your facilities.