Registration Dossier

Administrative data

First-aid measures

Description of first aid measures
After inhalation: fresh air.
After skin contact: wash off with plenty of water. Remove contaminated clothing.
After eye contact: rinse out with plenty of water.
After swallowing: make victim drink water (two glasses at most). Consult doctor if feeling unwell.

Most important symptoms and effects, both acute and delayed
irritant effects

Indication of any immediate medical attention and special treatment needed
No information available.

Fire-fighting measures

Extinguishing media
Suitable extinguishing media
Carbon dioxide (CO2), Foam, Dry powder
Unsuitable extinguishing media
For this substance/mixture no limitations of extinguishing agents are given.

Special hazards arising from the substance or mixture
Combustible.
Vapours are heavier than air and may spread along floors.
Forms explosive mixtures with air on intense heating.
Development of hazardous combustion gases or vapours possible in the event of fire.

Advice for firefighters
Special protective equipment for firefighters
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.
Further information
Prevent fire extinguishing water from contaminating surface water or the ground water system.

Accidental release measures

Personal precautions, protective equipment and emergency procedures
Advice for non-emergency personnel: Avoid substance contact. Do not breathe vapours, aerosols. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.
Advice for emergency responders: Protective equipment see section 8.respective section.

Environmental precautions
Do not let product enter drains

Methods and materials for containment and cleaning up
Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions. Take up with liquid-absorbent material (e.g. Chemizorb® ). Dispose of properly. Clean up affected area.

Reference to other sections
Indications about waste treatment see respective section.

Handling and storage

Precautions for safe handling
Advice on safe handling
Observe label precautions.
Hygiene measures
Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.

Conditions for safe storage, including any incompatibilities
Storage conditions
Tightly closed.
Recommended storage temperature see product label.

Specific end use(s)
Apart from the uses mentioned in IUCLID section 3 no other specific uses are stipulated.

Transport information

Land transport (ADR/RID)

UN number:
No dangerous good.
Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (ADN(R))

UN number:
No dangerous good.
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

UN number:
No dangerous good.
Remarksopen allclose all

Air transport ICAO/IATA

UN number:
No dangerous good.
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Exposure controls
Engineering measures
Technical measures and appropriate working operations should be given priority over the use of personal protective equipment.

Individual protection measures
Protective clothing needs to be selected specifically for the workplace, depending on concentrations and quantities of the hazardous substances handled. The chemical resistance of the protective equipment should be enquired at the respective supplier.

Eye/face protection
Safety glasses

Hand protection
splash contact:
Glove material: butyl-rubber
Glove thickness: 0,7 mm
Break through time: > 10 min

The protective gloves to be used must comply with the specifications of EC Directive 89/686/EEC and the related standard EN374, for example KCL 898 Butoject® (splash contact). This recommendation applies only to the product stated in the safety data sheet<(>,<)> supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).

Other protective equipment
protective clothing

Respiratory protection
required when vapours/aerosols are generated.

Recommended Filter type: filter ABEK
The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.

Environmental exposure controls
Do not let product enter drains.

Stability and reactivity

Reactivity
No critical reactivity known.

Chemical stability
The product is chemically stable under standard ambient conditions (room temperature) .

Possibility of hazardous reactions
Violent reactions possible with: Strong oxidizing agents

Conditions to avoid
Strong heating.

Incompatible materials
no information available

Disposal considerations

Waste treatment methods
See www.retrologistik.com for processes regarding the return of chemicals and containers, or contact us there if you have further questions.