3-methyl-1-phenylpyrazol-5-ylamine

Endpoint summary

Description of key information

Skin irritation:

The dermal irritation potential of chemical

3-methyl-1-phenylpyrazol-5-ylamine (CAS No: 1131-18-6) and read across chemicals were assessed in various in- vitro and in-vivo experimental studies. Based on the available key data, it can be concluded that the test chemical is unable to cause skin irritation and considered as notirritant. Comparing the above annotations with the criteria of CLP regulation, it can be classified under the category Not-classified as per the CLP regulation.

 

Eye irritation:

The ocular irritation potential of chemical 3-methyl-1-phenylpyrazol-5-ylamine (CAS No: 1131-18-6) and read across chemicals was assessed in various in- vitro and in-vivo experimental studies. Based on the available key data, it can be concluded that the test chemical is unable to cause eye irritation and considered as Notirritant. Comparing the above annotations with the criteria of CLP regulation, chemical can be classified under the category Not-classified as per the CLP regulation.

.  

Key value for chemical safety assessment

Skin irritation / corrosion

Link to relevant study records

Reference

Endpoint:

skin irritation: in vitro / ex vivo

Type of information:

experimental study

Adequacy of study:

key study

Reliability:

1 (reliable without restriction)

Rationale for reliability incl. deficiencies:

guideline study

Justification for type of information:

Data is from experimental study report

Qualifier:

according to guideline

Guideline:

OECD Guideline 439 (In Vitro Skin Irritation: Reconstructed Human Epidermis Test Method)

Principles of method if other than guideline:

The purpose of this study was to assess potential for the test article to be dermal irritants. The dermal irritation potential of test article may be predicted by measurement of their cytotoxic effect, as reflected in the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay, in the MatTek EpiDerm™ model.

GLP compliance:

no

Test system:

human skin model

Source species:

human

Cell type:

non-transformed keratinocytes

Cell source:

other: as provided by MatTek In Vitro Life Science Laboratories, Bratislava, Slovakia

Source strain:

other: Not applicable

Details on animal used as source of test system:

- Description of the cell system used:The normal human-derived keratinocytes were cultured at the air-liquid interface in a chemically defined medium on a permeable polycarbonate insert (surface 0.5 cm2). They were cultured in chemically defined serum free medium to form a multi-layered epithelium similar to that found in native epidermis. Each lot of tissues was Quality Assured by MatTek according to specific QC standards including: histology, tissue viability (MTT mean optical density), reproducibility (SD) and tissue thickness.Test System IdentificationAll of the EpiDerm™ 3-dimensional human tissues used in this study were identified by the date of arrival and the lot number. Certificate of Analysis for the tissues are included in this report. Tissue plates were appropriately labeled with study information.

Justification for test system used:

The 3-Dimensional Human Dermal Epithelial Model (EpiDerm™, MatTek, In Vitro Life Science Laboratories, Bratislava, Slovakia) is made up of normal human keratinocytes in serum free medium. The cells form an epithelial tissue that consists of organized basal, spinous, granular, and cornified layers analogous to those found in vivo. The EpiDerm™ model also contains epidermis-specific differentiation markers such as pro-filaggrin, the K1/K10 cytokeratin pair, involucrin, and type I epidermal transglutaminase, as well as keratohyalin granules, tonofilament bundles, desmosomes, and a multi-layered stratum corneum containing intercellular lamellar lipid layers arranged in patterns characteristic of in vivo epidermis. Each lot of tissues was Quality Assured by MatTek, Inc. according to specific QC standards including: histology (cell layers), tissue viability (MTT mean optical density) and reproducibility (SD). Tissue plates were appropriately labeled with study information. Bias was not a factor in this test system.

Vehicle:

unchanged (no vehicle)

Details on test system:

The tissues were exposed to the test article neat (undiluted) on April 25, 2018 (Run 1 of 1). EpiDerm™ tissues were purchased from MatTek. Quality control of the tissues was performed by MatTek and the Certificate of Analysis (CoA) for the tissues is provided and is kept in the study binder. Tissues were exposed for approximately 1 hour, with 35 minutes in an approximately 37°C, 5% CO2 humidified incubator and the remaining 25 minutes at room temperature. Following the exposure time, the tissues were rinsed and placed in fresh media for approximately 24 hours. The media was then changed again and the tissues were incubated in fresh media for another ~18 hours for a total of approximately 42 hour post-exposure recovery period. The tissue viability was then assessed by MTT assay. The tissue CoA was used instead of verification of barrier properties of the tissue.MTT and Color Pre-testsPretesting has actually been conducted for all chemicals, although the first intitial 8 test chemicals a pretesting was not conducted (for skin).MTT AssayFollowing the rinsing period, the MTT assay was performed by transferring the tissues to 24-well plates containing 300 µL MTT medium (1.0 mg/mL). After 3 hours MTT incubation at approximately 37°C, approximately 5% CO2 in a humidified incubator, the blue formazan salt was extracted by submerging tissues in 2 mL isopropanol in a 24-well plate. The extraction time was approximately 3 hours with gentle shaking. The optical density of the extracted formazan (200 µL/well of a 96-well plate) was determined using a Thermo Scientific Multiskan FC Microplate Photometer at 570 nm. Relative cell viability is calculated for each tissue as % of the mean negative control tissues.Evaluation of Test Article in the Cell Models:1. Cell system: Upon receipt, the MatTek EpiDerm™ tissue cultures were placed in 0.9 mL of fresh Maintenance medium (in a 6-well plate). The culture inserts are incubated for ~one hour. The tissues were then transferred to 6-well plates containing 0.9 mL fresh Maintenance medium and they were incubated overnight (18 ± 3 hrs) at ~37°C, 5% CO2 in a humidified incubator
.2. Control and Test Article Exposures: On the day of dosing, the tissues are then removed from the incubator and the controls and the test article are applied topically to tissues by pipette(liquid) Tissues were exposed to controls and the test article for one hour, with ~35 minutes in a 37°C, 5% CO2 humidified incubator and the remaining 25 minutes at room temperature.a) Controls30 µL of negative control DPBS and 30 μL of the positive control 5% SDS was applied topically to the tissue and gently spread by placing a nylon mesh on the apical surface of each tissue, if necessary.b) Test Articles 25 mg of the test article was applied topically to the tissue 3. Post-exposure treatment: After the 1 hour exposure, the tissues were rinsed 15 times with sterile DPBS. After the 15th rinse from washing bottle, each insert wasw completely submerge 3 times in 150 ml DPBS. The apical surface was gently blotted with a cotton swab. The tissues were placed in 0.9 mL of fresh Maintenance medium (6-well plate) for 24 ± 2 hours. After this initial ~24 hour incubation, the tissues were placed in 6-well plates containing 0.9 mL fresh Maintenance medium and incubated for another 18 ± 3 hours, for a total of an approximately 42 hour post-exposure incubation.RECONSTRUCTED HUMAN EPIDERMIS (RHE) TISSUE- Model used: The EpiDerm™ 3 dimensional human tissue model- Tissue Lot number(s): 26459- Date of initiation of testing: 6/08/2017TEMPERATURE USED FOR TEST SYSTEM- Temperature used during treatment / exposure: 37°C- Temperature of post-treatment incubation (if applicable): 37°CREMOVAL OF TEST MATERIAL AND CONTROLS-Volume and number of washing steps: The test substance was rinsed from the tissues with sterile DPBS by filling and emptying the tissue insert 15 times to remove any residual test material. This was followed by completely submerge the insert 3 times in 150 ml DPBS.MTT DYE USED TO MEASURE TISSUE VIABILITY AFTER TREATMENT / EXPOSURE- MTT concentration: 300 µL MTT medium (1.0 mg/mL).- Incubation time: After 3 hours- Spectrophotometer: Synergy H4 spectrophotometer - Wavelength: 570 nm- Filter: No data- Filter bandwidth: No data- Linear OD range of spectrophotometer: No dataNUMBER OF REPLICATE TISSUES: 3CALCULATIONS and STATISTICAL METHODSAll data were background subtracted before analysis. MTT data are presented as % viable compared to negative control. Data were generated as follows: MTT AssayBlanks:·        The optical density (OD) mean from all replicates for each plate (ODblank). Negative Controls (NC):·        The blank corrected value was calculated: ODNC= ODNCraw– ODblank. ·        The OD mean per NC tissue was calculated. ·        The mean OD for all tissues corresponds to 100% viability. ·        The mean, standard deviation (SD), standard error of the mean (SEM) and the percent coefficient of variation (% CV) was calculated. Positive Control (PC):·        Calculate the blank corrected value: ODPC= ODPCraw– ODblank. ·        The OD mean per PC tissue was calculated. ·        The viability per tissue was calculated: %PC = [ODPC/ mean ODNC] x 100. ·        The mean viability for all tissues was calculated: Mean PC = Σ %PC / number of tissues. ·        The standard deviation (SD), standard error of the mean (SEM) and the percent coefficient of variation (% CV) was calculated. Tested compound :·        Calculate the blank corrected value ODTT= ODTTraw– ODblank. ·        The OD mean per tissue was calculated. ·        The viability per tissue was calculated: %TT = [ODTT/ mean ODNC] x 100. ·        The mean viability for all tissues was calculated: Mean TT = Σ %TT / number of tissues. ·        The standard deviation (SD), standard error of the mean (SEM) and the percent coefficient of variation (% CV) was calculated. Data Correction Procedure for MTT Interfering Compounds (if applicable)True viability = Viability of treated tissue – Interference from test article = ODtvt– ODktwhere ODkt= (mean ODtkt– mean ODukt).ODtvt= optical density of treated viable tissueODkt= optical density of killed tissuesODtkt= optical density of treated killed tissueODukt= optical density of untreated killed tissue (NC treated tissue) Data Correction Procedure for Colored Compounds (if applicable)True viability = Viability of treated tissue incubated in MTT media – Viability of treated tissue incubated in media without MTT = ODtvt– ODvt.ODtvt= optical density of treated viable tissue incubated in MTT mediaODvt= optical density of viable tissues incubated in media alone - Evaluation of data The results of the assay was evaluated and compared to negative control. Table: Criteria for in vitro Interpretation: In VitroResults In VivoPredictionMean tissue viability ≤50% Irritant (I), R38Mean tissue viability >50% Non-irritant (NI)- Assay quality controls- Negative Controls (NC)The Dulbecco’s phosphate buffered saline (DPBS) was used as a NC. The assay passed all acceptance criteria if the ODs of the negative control exposed tissues were between ≥0.8 and ≤2.8.  - Positive Controls (PC)5% solution of sodium dodecyl sulfate was used as a PC. The assay is meeting the acceptance criteria if the viability of the PC is ≤20% of the negative control.   - Standard Deviation (SD)The standard deviation (SD) calculated from individual percent tissue viabilities of the test article exposed replicates was ≤18.

Control samples:

yes, concurrent negative control

yes, concurrent positive control

Amount/concentration applied:

TEST MATERIAL- Amount(s) applied (volume or weight with unit):25 mg- Concentration (if solution): neat VEHICLE (Not used)- Amount(s) applied (volume or weight with unit): none- Concentration (if solution): none- Lot/batch no. (if required): none- Purity: noneNEGATIVE CONTROL- Amount(s) applied (volume or weight): 30 µL sterile DPBS- Concentration (if solution): neatPOSITIVE CONTROL- Amount(s) applied (volume or weight): 30 µL- Concentration (if solution): 5% solution of sodium dodecyl sulfate

Duration of treatment / exposure:

The exposure times were approximately 1 hour, with ~35 minutes exposure in the incubator and ~25 minutes at room temperature.

Duration of post-treatment incubation (if applicable):

For a total of an approximately 42 hour post-exposure incubation.

Number of replicates:

3 tissues were used for test compound and control.

Type of coverage:

not specified

Preparation of test site:

not specified

Vehicle:

not specified

Controls:

not specified

Irritation / corrosion parameter:

% tissue viability

Run / experiment:

Run 1

Value:

95.3

Vehicle controls validity:

not specified

Negative controls validity:

valid

Positive controls validity:

valid

Remarks on result:

other: Mean of OD:2.164;non-irritant

Other effects / acceptance of results:

The MTT data show the assay quality controls were met.

Interpretation of results:

other: not irritating

Conclusions:

The dermal irritation potential of test article was determined according to the OECD 439 test guideline followed for this study. The mean of OD for test chemical was determined to be 2.164. The standard deviation of viabilities for test chemical were calculated to be 1.86.The Mean % tissue viability compared to negative control (n=3) of the test chemical was determined to be 95.3%. Thus, test chemical was considered to be not irritating to the human skin.

Executive summary:

The dermal irritation potential of test article was determined according to the OECD 439 test guideline for this study. The MatTek EpiDerm™ model was used to access the potential dermal irritation of the test article by determining the viability of the tissues following exposure to the test article via MTT. Tissues were exposed to the test article and controls for ~one hour, followed by a 42 hour post-exposure recovery period. The viability of each tissue was determined by MTT assay. 

The mean of OD for test chemical was determined to be 2.1164. The standard deviation of viabilities for test chemical were calculated to be 1.86.The Mean % tissue viability compared to negative control (n=3) of the test chemical was determined to be 95.3%. Thus, test chemical was considered to be not irritating to the human skin.

Endpoint conclusion

Endpoint conclusion:

no adverse effect observed (not irritating)

Eye irritation

Link to relevant study records

Reference

Endpoint:

eye irritation: in vitro / ex vivo

Type of information:

experimental study

Adequacy of study:

key study

Reliability:

1 (reliable without restriction)

Rationale for reliability incl. deficiencies:

guideline study

Justification for type of information:

Data is from experimental study report.

Qualifier:

according to guideline

Guideline:

OECD Guideline 492 (Reconstructed Human Cornea-like Epithelium (RhCE) Test Method for Identifying Chemicals Not Requiring Classification and Labelling for Eye Irritation or Serious Eye Damage)

Principles of method if other than guideline:

The purpose of this study was to assess potential for the test article to be ocular irritants. The ocular irritation potential of a test article may be predicted by measurement of its cytotoxic effect, as reflected by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay, in the MatTek EpiOcular™ model.

GLP compliance:

no

Species:

human

Strain:

other: Not applicable

Details on test animals or tissues and environmental conditions:

- Description of the cell system used:The normal human-derived keratinocytes were cultured at the air-liquid interface in a chemically defined medium on a permeable polycarbonate insert (surface 0.5 cm2). They were cultured in chemically defined serum free medium to form a multi-layered epithelium similar to that found in native corneal mucosa. Each lot of tissues was Quality Assured by MatTek according to specific QC standards including: histology, tissue viability (MTT mean optical density), reproducibility (SD) and tissue thickness.- Test System IdentificationAll of the EpiOcular™ 3-dimensional human tissues used in this study were identified by the date of arrival and the lot number. Certificate of Analysis for the tissues is included in this report. Tissue plates were appropriately labeled with study information. Bias was not a factor in this test system.- Justification of the test method and considerations regarding applicabilityEpiOcularTM Eye Irritation (OCL) by MatTek In Vitro Life Science Laboratories, Bratislava, SlovakienThe test articles and controls were evaluated for potential ocular irritancy using the EpiOcular™ 3 dimensional human tissue model purchased from MatTek In Vitro Life Science Lab. (Bratislava, Slovakia). The EpiOcular tissue construct is a nonkeratinized epithelium prepared from normal human keratinocytes (MatTek). It models the cornea epithelium with progressively stratified, but not cornified cells. These cells are not transformed or transfected with genes to induce an extended life span in culture. The “tissue” is prepared in inserts with a porous membrane through which the nutrients pass to the cells. A cell suspension is seeded into the insert in specialized medium. After an initial period of submerged culture, the medium is removed from the top of the tissue so that the epithelial surface is in direct contact with the air. This allows the test material to be directly applied to the epithelial surface in a fashion similar to how the corneal epithelium would be exposed in vivo. Each lot of tissues was Quality Assured by MatTek, Inc. according to specific QC standards including: histology (cell layers), tissue viability (MTT mean optical density) and reproducibility (SD).

Vehicle:

unchanged (no vehicle)

Controls:

other: See ''Remark" for Control Samples used in the study

Amount / concentration applied:

TEST MATERIAL - Amount(s) applied (volume or weight with unit): 50 mg of solid test article - Concentration (if solution): neat (undiluted) VEHICLE (no vehicle) - Amount(s) applied (volume or weight with unit): none - Concentration (if solution): none - Lot/batch no. (if required): none - Purity: noneNEGATIVE CONTROL- Amount(s) applied (volume or weight): 50 µL- Concentration (if solution): neatPOSITIVE CONTROL- Amount(s) applied (volume or weight): 50 µL- Concentration (if solution): neat

Duration of treatment / exposure:

Tissues were exposed for approximately 30 minutes for liquid test article and controls 6 hrs ± 15 min for solid test articles, at approximately 37°C, 5% CO2 in a humidified incubator.

Observation period (in vivo):

Not applicable

Duration of post- treatment incubation (in vitro):

Following the washing step and the post-soak, the tissues were incubated at approximately 37°C, 5% CO2 in a humidified incubator for a post-exposure recovery time of ~2 hours for 18 hrs for solid test articles, or 18 hrs for solid test articles, and controls.

Number of animals or in vitro replicates:

2 tissues were used for test compound and control.

Details on study design:

- Details of the test procedure usedThe tissues were exposed to the test article neat (undiluted). EpiOcular™ tissues were purchased from MatTek. Quality control of the tissues was performed by MatTek and the Certificate of Analysis (CoA) for the tissues is provided and is kept in the study binder. Tissues were exposed for approximately 6 hrs ± 15 min for solid test articles, and controls, at approximately 37°C, 5% CO2 in a humidified incubator. After the exposure, the test article was rinsed off the tissues and the tissues were soaked in media for ~12 minutes for 25 min for solid test articles articles and controls. Following the washing step and the, the tissues were incubated at approximately 37°C, 5% CO2 in a humidified incubator for a post-exposure recovery time totaling ~2 hours for 18 hrs for solid articles and controls. Tissue viability was assessed by 3-(4,5-dimethylthiazol- 2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay. - MTT Auto reduction and colouring assessmentMTT Pre-testThe test article was assessed for the potential to interfere with the assay. Approximately 50 µL of liquid test article was added to 1 mL of MTT media (~1 mg/mL) and incubated in a humidified incubator at approximately 37°C and approximately 5% CO2 for 3 hours. 50 µL of ultrapure water was used as a negative control. - Test Article Color TestApproximately 50 µL of liquid test article was added to 1.0 mL of ultrapure water and 2.0 mL isopropanol and incubated in a humidified incubator at approximately 37°C and approximately 5% CO2 for 2 hours, 04 minutes and 35 seconds. Samples were then added to the wells of a clear 96-well plate and the plate was read on a Thermo Scientific Multiskan FC Microplate Photometer to 570 nm. Test articles that tested positive for excessive coloration (OD >0.08) were assessed on living-tissue controls that were incubated in both culture media and MTT media as well (n=3 for both conditions). - MTT Assay Solids: Inserts are removed from the 24-well plate after 3 hrs of incubation and the bottom of the insert is blotted on absorbent material, and then transferred to a pre-labeled 6-well plate containing 1 ml isopropanol in each well so that no isopropanol is flowing into the insert. At the end of the non-submerged extraction inserts and tissues are discarded without piercing and 1 ml of isopropanol is added into each well. The extract solution is mixed and the optical density of the extracted formazan (200 μL/well of a 96-well plate) was determined using aThermo Scientific Multiskan FC Microplate Photometer at 570 nm. Relative cell viability was calculated for each tissue as % of the mean negative control - Evaluation of Test Article in the cell Models1. Cell System: Upon receipt, the MatTek EpiOcular™ tissue cultures were placed in 1.0 mL of fresh Maintenance medium (in a 6-well plate) for 60 minutes. After the 60 minutes incubation, the Maintenance medium was exchanged with fresh medium and the tissues were incubated overnight (16-24 hrs) at approximately 37°C, approximately 5% CO2 in a humidified incubator,2. Control and Test Article Exposures:20 µL of calcium and magnesium free DPBS was added to each tissue and the tissues placed back into the incubator for 30 minutes. The controls and the test article will be applied topically to tissues by pipette. Three tissues will be used per test compound and control.a)Controls: 50 µL of negative control sterile ultrapure water and positive control methyl acetate were added to the tissues. The tissues were placed into the ~37°C humidified incubator with 5% CO2 for the approximately 30 minute exposure time. b)Test Article: When a solid was tested, 50 mg of the solid were added to the tissues. The tissues were placed into the ~37°C humidified incubator with 5% CO2 for the approximately 6 hrs ± 15 min. 3. Post exposure treatment:After the exposure, the tissues were rinsed 20 times with sterile of DPBS to remove test material. The apical surface was gently blotted with a cotton swab and cultures were immediately transferred to a 12-well plate containing 5 mL of media per well. Tissues exposed to solid test articles (and the respective control) were incubated, submerged in the media for ~12 minutes at room temperature.For liquid test articles, tissues, Tissuses were then transferred to 6-well plates containing 1.0 mL fresh Maintenance medium per well and incubated for a post-exposure recovery period for 18 hrs overnight at approximately 37 degC, 5% CO2 in a humidified incubator.- Doses of test chemical and control substances usedTest Article: 50 mg of solid test article were added to the tissues. The tissues were placed into the ~37°C humidified incubator with 5% CO2 for the approximately 6 hrs exposure time Controls: 50 µL of negative control sterile ultrapure water, positive control methyl acetate were added to the tissues. The tissues were placed into the ~37°C humidified incubator with 5% CO2 for the approximately 6 hrs exposure time. - Duration and temperature of exposure, post-exposure immersion and post-exposure incubation periods: Tissues were exposed for approximately 30 minutes for 6 hrs for solid test articles and controls, at approximately 37°C, 5% CO2 in a humidified incubator. Following the washing step and the, the tissues were rinsed and incubated at approximately 37°C, 5% CO2 in a humidified incubator for a post-exposure recovery time totaling ~2 hours for liquid test articles and controls.- Justification for the use of a different negative control than ultrapure H2O (Not applicable)- Justification for the use of a different positive control than neat methyl acetate (Not applicable)- Number of tissue replicates used per test chemical and controls: 2 tissues were used for test compound and control.- Description of the method used to quantify MTT formazanThe blue formazan salt was extracted by submerging tissues in 2 mL isopropanol in a 24-well plate. The extraction for liquid exposed tissues was overnight incubation with a 20 minute 24 second shake the following morning. The optical density of the extracted formazan (200 µL/well of a 96-well plate) was determined using a Thermo Scientific Multiskan FC Microplate Photometer at 570 nm. The blue formazan salt was extracted by placing the tissue insterts in 1 mL isopropanol in a 6-well plate. The extraction for solid exposed tissues was 3 hrs incubation. After an addition of 1 ml isopropanol and mixing, the optical density of the extracted formazan (200μL/well of a 96-well plate) was determined using a Thermo Scientific Multiskan FC Microplate Photometer at 570 nm.- Description of evaluation criteria used including the justification for the selection of the cut-off point for the prediction modelCalculations and Statistical MethodsMTT AssayBlanks: ·  The OD mean from all replicates for each plate (ODblank). Negative Controls (NC): ·  The blank corrected value was calculated: ODNC= ODNCraw– ODblank. ·  The OD mean per NC tissue was calculated. ·  The mean OD for all tissues corresponds to 100% viability. ·  The mean, standard deviation (SD), standard error of the mean (SEM) and the percent coefficient of variation (% CV) was calculated. ODblank= optical density of blank samples (isopropanol alone). ODNCraw= optical density negative control samples. ODNC= optical density of negative control samples after background subtraction. Positive Control (PC): ·        Calculate the blank corrected value: ODPC= ODPCraw– ODblank. ·        The OD mean per PC tissue was calculated. ·        The viability per tissue was calculated: %PC = [ODPC/ mean ODNC] x 100. ·        The mean viability for all tissues was calculated: Mean PC = Σ %PC / number of tissues. ·        The standard deviation (SD), standard error of the mean (SEM) and the percent coefficient of variation (% CV) was calculated. ODPCraw= optical density positive control samples. ODPC= optical density of positive control samples after background subtraction. Tested Articles: ·  Calculate the blank corrected value ODTT= ODTTraw– ODblank. ·  The OD mean per tissue is calculated. ·  The viability per tissue is calculated: %TT = [ODTT/ mean ODNC] x 100. ·  The mean viability for all tissues is calculated: Mean TT = Σ %TT / number of tissues. ·  The standard deviation (SD) and the percent coefficient of variation (% CV)for the controls and the test articles will be calculated. ODTTraw= optical density test article samples. ODPC= optical density of test article samples after background subtraction. Data Correction Procedure for MTT Interfering CompoundsTrue viability = Viability of treated tissue – Interference from test article = ODtvt – ODkt where ODkt = (mean ODtkt – mean ODukt). ODtvt = optical density of treated viable tissue ODkt = optical density of killed tissues ODtkt = optical density of treated killed tissue ODukt = optical density of untreated killed tissue (NC treated tissue) Data Correction Procedure for Colored CompoundsTrue viability = Viability of treated tissue incubated in MTT media – Viability of treated tissue incubated in media without MTT = ODtvt – ODvt. ODtvt = optical density of treated viable tissue incubated in MTT media ODvt = optical density of viable tissues incubated in media alone. Proposed Statistical methods The mean, standard deviation (SD) and the percent coefficient of variation (% CV) for the controls and the test article will be calculated. - Evaluation of data The results of the assay was evaluated and compared to negative control. Table: Irritancy Prediction In VitroResults In VivoPredictionMean tissue viability ≤60% Irritant (I) – Category 1 or 2Mean tissue viability >60% Non-irritant (NI) – No Category- Assay quality controls- Negative Controls (NC)The assay is meeting the acceptance criterion if the mean viability of the NC in terms of Optical Density (OD570) of the NC tissues (treated with sterile ultrapure water) in the MTT assay are >0.8 to <2.5. This is an indicator of tissue viability following shipping and conditions under use.   - Positive Controls (PC)Methyl acetate was used as a PC and tested concurrently with the test article. The assay is meeting the acceptance criteria if the viability of the PC is <50% of the negative control.   - Standard Deviation (SD)Each test of ocular irritancy potential is predicted from the mean viability determined on 3 single tissues. The assay meets the acceptance criteria if SD calculated from individual percent tissue viabilities of the replicates is <18% for three replicate tissues.  

Irritation parameter:

other: mean % tissue viability

Run / experiment:

Run 1

Value:

63.1

Vehicle controls validity:

not specified

Negative controls validity:

valid

Positive controls validity:

valid

Remarks on result:

other: Mean of OD:1.367;non-irritant

Other effects / acceptance of results:

The MTT data show the assay quality controls were met.

Interpretation of results:

other: not irritating

Conclusions:

The ocular irritation potential of test article was determined according to the OECD 492 test guideline followed for this study. The mean of OD for test chemical was determined to be 1.367.The mean % tissue viability of test substance was determined to be 63.1%. Thus, test chemical was considered to be not irritating to the human eyes.

Executive summary:

The ocular irritation potential of test article was determined according to the OECD 492 test guideline for this study. The MatTek EpiOcular™ model was used to assess the potential ocular irritation of the test articles by determining the viability of the tissues following exposure to the test article via MTT.  Tissues were exposed to solid test articles and control for approx.6 hours, followed by a 25 minute post-soak and approximately 18 hours recovery after the post-soak.  The viability of each tissue was determined by MTT assay.  The MTT data show the assay quality controls were met, and passing the acceptance criteria. The mean of OD for test chemical was determined to be 1.367.The mean % tissue viability of test chemical was determined to be 63.1%. Hence, under the experimental test conditions it was concluded that test chemical was considered to be not irritating to the human eyes.

Endpoint conclusion

Endpoint conclusion:

no adverse effect observed (not irritating)

Respiratory irritation

Endpoint conclusion

Endpoint conclusion:

no study available

Additional information

Skin irritation:

Various studies has been investigated for the test chemical 3-methyl-1-phenylpyrazol-5-ylamine (CAS No: 1131-18-6) to observe the potential for dermal irritation to a greater or lesser extent. The studies are based on in-vitro and in-vivo experiments for 3-methyl-1-phenylpyrazol-5-ylamine and read across chemicals which have been summarized as below:

 

In the first key in-vitro study dermal irritation potential of test article was determined according to the OECD 439 test guideline for this study. The MatTek EpiDerm™ model was used to access the potential dermal irritation of the test article by determining the viability of the tissues following exposure to the test article via MTT. Tissues were exposed to the test article and controls for ~one hour, followed by a 42 hour post-exposure recovery period. The viability of each tissue was determined by MTT assay.  The mean of OD for test chemical was determined to be 2.1164. The standard deviation of viabilities for test chemical were calculated to be 1.86.The Mean % tissue viability compared to negative control (n=3) of the test chemical was determined to be 95.3%. Thus, test chemical was considered to be not irritating to the human skin.

 

Above study was supported by the second study from experimental report. The study was designed and conducted to determine the dermal Irritation/corrosion potential of the test chemical in Sprague Dawley rats. This study was performed as per OECD guideline No. 402. Ten rats (5 male and 5 female) were used for conducting dermal irritation/ corrosion study. The animals were kept in their cages for at least 5 days prior to administration for acclimatization to the laboratory condition and after acclimatization period, animals were randomly selected. Approximately 24 hours before application, the hair of each rat was closely clipped from the trunk (dorsal surface and sides from scapular to pelvic area) with an electric clipper, so as to expose at least 10% of the body surface area. The test item was moistened with distilled water. The test item was applied onto the exposed skin of the animal, taking care to spread the test item evenly over the entire area of approximately 10% of the total body surface area or as much of the area as can reasonably be covered. The test item was held in contact with the skin using a porous gauze dressing and non-irritating tape around the animal to cover the exposure site for first 24 hours exposure period. Elizabethan collar was placed on each animal for first 24 hours after application of the test item. These collars prevent ingestion of test item. Following 24 hours of exposure, the wrapping was removed and the test site wiped free of excess test item. Distilled water was used to remove residual test item. The test chemical was applied to shorn skin of 5 male and 5 female animals at 2000 mg/kg body weight. Administration of the test item at 2000 mg/kg did not result in any skin reaction at the site of application during the study period of 14 days. Also, the erythema and edema score of rats was calculated as 0. Administration of the test item did not result in any signs of toxicity and mortality during the study period of 14 days. Animals exhibited normal body weight gain through the study period of 14 days. Gross pathological examination did not reveal any abnormalities attributable to the treatment. Hence, it was concluded that the test chemical was Non-Irritating to the skin of Sprague Dawley rats under the experimental conditions tested and Classified as “Category- Not Classified” as per CLP Classification.

Similar study was designed and conducted to determine the dermal reaction profile of the test chemical in Sprague Dawley rats. This study was performed as per OECD guideline No. 402. Ten rats (5 male and 5 female) were used for conducting dermal irritation/ corrosion study. The animals were kept in their cages for at least 5 days prior to administration for acclimatization to the laboratory condition and after acclimatization period, animals were randomly selected. Approximately 24 hours before application, the hair of each rat was closely clipped from the trunk (dorsal surface and sides from scapular to pelvic area) with an electric clipper, so as to expose at least 10% of the body surface area. The test item was moistened with distilled water. The test item was applied onto the exposed skin of the animal, taking care to spread the test item evenly over the entire area of approximately 10% of the total body surface area or as much of the area as can reasonably be covered. The test item was held in contact with the skin using a porous gauze dressing and non irritating tape around the animal to cover the exposure site for first 24 hours exposure period. Elizabethan collar was placed on each animal for first 24 hours after application of the test item. These collars prevent ingestion of test item. Following 24 hours of exposure, the wrapping was removed and the test site wiped free of excess test item. Distilled water was used to remove residual test item. The test chemical was applied to shorn skin of 5 male and 5 female animals at 2000 mg/kg body weight. Administration of the test item at 2000 mg/kg did not result in any skin reaction at the site of application during the study period of 14 days. Also, the erythema and edema score of rats was calculated as 0. Administration of the test item did not result in any signs of toxicity and mortality during the study period of 14 days.  Animals exhibited normal body weight gain through the study period of 14 days. Gross pathological examination did not reveal any abnormalities attributable to the treatment. Hence, it was concluded that the test chemical was Non-Irritating to the skin of Sprague Dawley rats under the experimental conditions tested and Classified as “Category- Unclassified” as per CLP Classification.

 

In the fourth study acute Dermal Irritation/corrosion Study of “Benzyl propionate(CAS No. -122-63-4)”in Rabbits, was performed in a OECD GLP laboratory (Sustainability Support Services (Europe) AB has the letter of access). This study was performed as per OECD guideline No. 404. Three healthy young adult female rabbits were used for conducting acute dermal irritation study. Body weights were re­corded on day 0 (prior to application) and at termination. Rabbits with good intact skin were selected for the study. The hairs of all the rabbits were clipped at contralateral sites, approximately 24 hours prior to treatment. A dose of0.5 ml of test item (as such) was applied to the skin, over an area of approximately 6 x 6 cm clipped of hair on one side of rabbits. The other untreated side was kept as control area and 0.5 ml of distilled water was applied at this site. At the end of 4 hours, the gauze patch was removed and test item application site was wiped with water without altering the integrity of the epidermis. Initially, the test item was applied to the clipped area of skin of one rabbit. The test site was covered with gauze patch. After 4 hours of exposure in Animal No. 1, there was no erythema and oedema observed at 1, 24, 48 and 72 hours observation. Hence the confirmatory test was conducted on additional two rabbits (No. 2 and 3)to confirm the nonirritant nature of the test item. In Animals No. 2 and 3 after post patch removal, revealed no erythema and edema at 1, 24, 48 and 72 hours observation. The patch was removed after 4 hours and rabbits were observed for erythema and oedema at 1, 24, 48 and 72 hours after patch removal, evaluated and graded as per Draize method. The individual mean score at 24, 48 and 72 hours for Animal Nos. 1, 2 and 3 were 0.00, 0.00, 0.00 and 0.00, 0.00, 0.00, for erythema and oedema formation, respectively. Hence, it was concluded that “Benzyl propionate (CAS No. - 122 -63-4)” was Non-Irritating to the skin of Female New Zealand White rabbits under the experimental conditions tested and Classified as “Category- Not Classified” as per CLP Regulation.

 

Thus on the basis of experimental key study, chemical consider to be Non-Irritating to the skin and Classified as “Category- Not Classified” as per CLP Regulation.

 

Eye irritation:

Various studies has been investigated for the test chemical 3-methyl-1-phenylpyrazol-5-ylamine (CAS No: 1131-18-6) to observe the potential for ocular irritation to a greater or lesser extent. The studies are based on in-vitro and in-vivo experiments which have been summarized as below;

 

The ocular irritation potential of test article was determined according to the OECD 492 test guideline for this study. The MatTek EpiOcular™ model was used to assess the potential ocular irritation of the test articles by determining the viability of the tissues following exposure to the test article via MTT.  Tissues were exposed to solid test articles and control for approx.6 hours, followed by a 25 minute post-soak and approximately 18 hours recovery after the post-soak.  The viability of each tissue was determined by MTT assay.  The MTT data show the assay quality controls were met, and passing the acceptance criteria. The mean of OD for test chemical was determined to be 1.367.The mean % tissue viability of test chemical was determined to be 63.1%. Hence, under the experimental test conditions it was concluded that test chemical was considered to be not irritating to the human eyes.

 

Above study was supported by the second study from experimental report. Acute Ocular Irritation/corrosion Study of “Benzyl propionate(CAS No. -122-63-4)”in Rabbits, was performed in an OECD GLP laboratory (Sustainability Support Services (Europe) AB has the letter of access). This study was performed as per OECD guideline No. 405. Rabbits free from injury of eye were selected for the study. The eyes of all the rabbits were examined 24 hours prior to treatment. One eye of each rabbit served as control and other as treated. Control eye was left untreated whereas;0.1 ml of test item (as such)was instilled in the other (treated) eye of rabbits. The eye was observed at 1, 24, 48, 72 hours after test item instillation. Ophthalmoscope was used for scoring of eye lesions. In the initial test, 0.1 ml of test item was applied into the conjunctival sac of the right eye of Animal No.1. The left eye of the rabbit served as the control. Animal No. 1 presented ocular lesions at 1 hour observation period. Hence the confirmatory test was conducted on additional two rabbits (Animal No. 2 and 3); 0.1 ml of test item was instilled into the conjunctival sac of right eye and left eye served as the control. Ocular lesions were observed at 1, 24 and 48 hour in Animal Number 2 whereas in Animal Number 3 ocular lesions presented only at 1 hour observation period. Untreated eye of the treated rabbits was normal throughout the experimental period of 72 hours. The following grading scores were observed in treated eye of tested rabbits. Observation at 1 hour after instillation of test item revealed: Cornea-No ulceration or opacity in all 3 animals; Area of Opacity-Zero in all the animals;Iris:Normal in all the animals.Conjunctivae -Some blood vessels definitely hyperaemic (injected) in all the animals;Chemosis:Some swelling above normal (includes nictating membranes) were observed in animal number 1 and 3 whereas animal number 2 was normal. Observation at 24 hours after instillation of test item revealed: Cornea-No ulceration or opacity in all the animals; Area of Opacity-Zero in all the animals;Iris:Normal in all the animals.Conjunctivae -Some blood vessels definitely hyperaemic (injected) was observed in animal no. 2. Animal no. 1 and 3 recovered to normal;Chemosis:No swelling was observed in all the Animals. At 24 hours observation the rabbits were examined for corneal epithelium cell damage using sodium fluorescein strips and noticed 0 % damage in Animal Nos 1, 2 and 3, respectively. Observation at 48 and 72 hours after instillation of test item revealed: Cornea-No ulceration or opacity in all the animals; Area of Opacity-Zero in all the animals;Iris:Normal in all the animals.Conjunctivae -Some blood vessels definitely hyperaemic (injected) was observed in animal no. 3 at 48 hours which was recovered to normal at 72 hours observation whereas blood vessels were normal in Animal Numbers 1 and 3 at 48 and 72 hours observation; Chemosis:No swelling was observed in all the animals. The individual mean score for Animal Nos. 1, 2 and 3at 24, 48, 72 hours for Corneal opacity, iris, conjunctiva, chemosis were found 0.00, 0.00, 0.00, 0.00 ; 0.00, 0.00, 0.67, 0.00 and 0.00, 0.00, 0.00, 0.00, respectively. Under the experimental conditions tested, eye irritation and reversibility of effects on eyes of rabbits was observed at 72 hours. Hence under the experimental test conditions, Benzyl propionate (CAS No. - 122-63-4) is “Non Irritant” to New Zealand White Male rabbit eyes and is being classified as “Not Classified” as per the CLP regulation.

 

Similarly the test chemical was evaluated for in vivo eye irritation in rabbits. The tests were performed according to EEC (1984 and 1991) and French (1984 and 1991) directives with few modifications: ocular lesions (cornea, iris and conjunctiva) were scored. Three rabbits were used per test compound, and maximal average score (MAS) as well as score at day 1 were calculated. At the request of the participants, any mass of material present in the conjunctival sac was removed after the 1-hr observation. Also, a fluorescein solution was used for observation of corneal lesions. Only ocular lesions (cornea, iris and conjunctiva) were scored (Draize et al.,1944) at 1 hr, then at 1, 2, 3, 4, 7 and 14 days. In the case of positive score, eyes were also examined at 21 days. Raw data were also used to classify chemicals according to the rating system described by Kay and Calandra (1962), and the EC criteria (1984). The MAS score for the test chemical was calculated to be 8.7 and score measured at day 1 was found to be 7.7. The test chemical was classified as Nonirritant according to EEC(1984) directives and Mild irritant according toKay and Calandra (1962).

 

Thus on the basis of experimental key study, chemical consider to be Non-Irritating to the eye and Classified as “Category- Not Classified” as per CLP Regulation.

Justification for classification or non-classification

The skin and eye irritation potential of test chemical 3-methyl-1-phenylpyrazol-5-ylamine (CAS No: 1131-18-6) were observed in various studies. The results obtained from these studies indicate that the chemical is not likely to cause skin irritation as well as eye irritation. Hence the test chemical 3-methyl-1-phenylpyrazol-5-ylamine (CAS No: 1131-18-6) chemical consider to be Non-Irritating to the skin and eye and Classified as “Category- Not Classified” as per CLP Regulation.