Registration Dossier

Administrative data

First-aid measures

Description of first aid measures
Skin
Wash with soap and water for 20 minutes or until chemical is removed. Immediately remove all contaminated clothing. If skin irritation or rash occurs: Get medical attention. Launder contaminated clothing before reuse and discard leather articles saturated with the material.

Eyes
Rinse cautiously with water for 30 minutes. Remove contact lenses, if present and easy to do. Get medical attention if eye irritation develops or persists.

Inhaled
Remove exposed person to fresh air if adverse effects are observed.

Swallowed
Swallowing is an unlikely route of exposure. DO NOT INDUCE VOMITING. Get immediate medical attention.

Advice for first-aid providers
When providing first aid always protect yourself against exposure to chemicals or blood born diseases by wearing gloves, masks and eye protection. After providing first aid wash your exposed skin with soap and water.

Most important symptoms and effects, both acute and delayed
See section “Toxicological Information”.

Indication of any immediate medical attention and special treatment needed
Get medical attention advice if you feel unwell.

Fire-fighting measures

Fire Fighting Measures

Extinguishing Media
CO2, dry chemical, or foam. Water can be used to cool and protect exposed material.

Special hazards arising from substance or mixture
See section “Stability and Reactivity” for additional information.

Advice for firefighters
Wear full protective firegear including self-containing breathing apparatus operated in the positive pressure mode with full facepiece, coat, pants, gloves and boots. Do not use a water jet.

Accidental release measures

Accidental Release Measures

Personal precautions, protective equipment and emergency procedures
Personal protective equipment must be worn. Avoid contact with skin, eyes or clothing. Ventilate area if spilled in a confined space or other poorly ventilated
area.

Environmental precautions
Prevent entry into sewers and waterways.

Methods and material for containment and cleaning up
Pick up free liquid for recycle and/or disposal. Residual liquid can be absorbed on inert material.

Reference to other sections
See sections “Exposure Controls/Personal Protection” and “Toxicological Information” for additional information.

Handling and storage

Handling and Storage

Precautions for safe handling
Use with adequate ventilation. Keep containers closed and upright when not in use. When handling, do not eat, drink, or smoke Avoid drinking, tasting, swallowing or ingesting this product. Avoid breathing vapor. Avoid contact with eyes, skin and clothing Avoid overheating. Wash thoroughly after handling. Contaminated work clothing should not be allowed out of the workplace. Launder contaminated clothing before reuse. Do not reuse empty containers. Empty container contains product residue which may exhibit hazards of product. Dispose of packaging or containers in accordance with local, regional, national and international regulations.

Pumping Temperature
Not determined.

Maximum Handling Temperature
70 °C, 158 °F

Maximum Loading Temperature
Not determined.

Conditions for safe storage, including any incompatibilites
Store in a cool, dry, well-ventilated area. Store separately from incompatible materials. Keep container closed when not in use. Do not store in open, unlabeled or mislabeled containers. See section 10 for incompatible materials.

Maximum Storage Temperature
45 °C, 113 °F

Specific end use(s)
End uses are listed in an attached exposure scenario when one is required.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Exposure Controls/Personal Protection
Control parameters
None known.

Other Exposure Limits
Contains mineral oil. Under conditions which may generate mists, observe the OSHA PEL of 5 mg per cubic meter, ACGIH TWA of 5 mg per cubic meter.

Exposure controls
Material should be handled in enclosed vessels and equipment, in which case general (mechanical) room ventilation should be sufficient. Local exhaust ventilation should be used at points where dust, mist, vapors or gases can escape into the room air. Additional ventilation or exhaust may be required to maintain air concentrations below recommended exposure limits.

Eye/face protection
Safety glasses. If potential for splash or mist exists, wear chemical goggles or faceshield.

Skin protection
Nitrile. Gloves are recommended when handling this material. Unless material is used in a process where the use of gloves would pose sufficient risk of injury to the user/operator. Consult with an industrial hygienist to determine the appropriate clothing protection for your specific use of this material.
Long sleeve shirt is recommended. Use chemically protective boots when necessary to avoid contaminating shoes. Do not wear rings, watches or similar apparel that could entrap the material and cause a skin reaction. Launder contaminated clothing before reuse.

Respiratory Protection
Use respirator with a combination organic vapor and high efficiency filter cartridge if recommended exposure limit is exceeded. Use self-contained breathing apparatus for entry into confined space, for other poorly ventilated areas and for large spill clean-up sites. Consult with an industrial hygienist to determine the appropriate respiratory protection for your specific use of this material. A respiratory protection program compliant with all applicable regulations must be followed whenever workplace conditions require the use of a respirator.

Hygiene Measures
Wash thoroughly after handling this product. Do not eat, drink or smoke when using this product.

Environmental exposure controls
See section “Accidental Release Measures” for details.

Stability and reactivity

Stability and Reactivity
Reactivity
Carefully review all information provided in the following sections.

Chemical stability
Material is normally stable at moderately elevated temperatures and pressures.

Possibility of hazardous reactions
Will not occur.

Conditions to avoid
Not determined.

Incompatible materials
Oxidizing agents.

Hazardous decomposition products
Smoke, carbon monoxide, carbon dioxide, aldehydes and other products of incomplete combustion. Under combustion conditions, oxides of the following elements will be formed: calcium, sulfur.

Disposal considerations

Waste treatment methods
All disposal practices must be in accordance with local, regional, national and international regulations. Do not dispose in landfill.
Dispose of packaging or containers in accordance with local, regional, national and international regulations.