Registration Dossier

Diss Factsheets

Administrative data

First-aid measures

General advice:

Remove contaminated clothing.

If inhaled:

Keep patient calm, remove to fresh air, seek medical attention.

On skin contact:

Wash thoroughly with soap and water.

On contact with eyes:

Wash affected eyes for at least 15 minutes under running water with eyelids held open, consult an eye

specialist.

On ingestion:

Immediately rinse mouth and then drink 200-300 ml of water, seek medical attention.

Note to physician:

Treatment: Treat according to symptoms (decontamination, vital functions), no known specific

antidote.

Fire-fighting measures

Suitable extinguishing media:

carbon dioxide, dry powder, water spray, foam

Special protective equipment:

Wear self-contained breathing apparatus and chemical-protective clothing.

Further information:

Collect contaminated extinguishing water separately, do not allow to reach sewage or effluent

systems.

Accidental release measures

Personal precautions:

Handle in accordance with good industrial hygiene and safety practice.

Environmental precautions:

Do not empty into drains.

Methods for cleaning up or taking up:

For large amounts: Pump off product.

For residues: Pick up with suitable absorbent material (e.g. sand, sawdust, general-purpose binder,

kieselguhr). Dispose of absorbed material in accordance with regulations.

Handling and storage

Handling

Ensure thorough ventilation of stores and work areas. Protect from direct sunlight.

Protection against fire and explosion:

Prevent electrostatic charge - sources of ignition should be kept well clear - fire extinguishers should

be kept handy.

Storage

Segregate from acids and acid forming substances.

Storage stability:

Storage temperature: <= 25 °C

Storage duration: 12 Months

The product is stabilized, the shelf life should be noted.

From the data on storage duration in this safety data sheet no agreed statement regarding the

warrantee of application properties can be deduced.

additives:

4-Hydroxy-2,2,6,6-tetramethylpiperidinoxyl (CAS Number: 2226-96-2)

Content: 0.002 %

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

Shippingopen allclose all
Remarksopen allclose all
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Personal protective equipment

Respiratory protection:

Breathing protection if gases/vapours are formed. Gas filter for gases/vapours of organic compounds

(boiling point >65 °C, e. g. EN 14387 Type A)

Hand protection:

Chemical resistant protective gloves (EN 374)

Suitable materials also with prolonged, direct contact (Recommended: Protective index 6,

corresponding > 480 minutes of permeation time according to EN 374):

nitrile rubber (NBR) - 0.4 mm coating thickness

fluoroelastomer (FKM) - 0.7 mm coating thickness

Supplementary note: The specifications are based on tests, literature data and information of glove

manufacturers or are derived from similar substances by analogy. Due to many conditions (e.g.

temperature) it must be considered, that the practical usage of a chemical-protective glove in practice

may be much shorter than the permeation time determined through testing.

Manufacturer's directions for use should be observed because of great diversity of types.

Eye protection:

Safety glasses with side-shields (frame goggles) (e.g. EN 166)

General safety and hygiene measures:

Handle in accordance with good industrial hygiene and safety practice. Wearing of closed work

clothing is required additionally to the stated personal protection equipment.

Stability and reactivity

Hazardous reactions:

Polymerization occurs with acids. The product can polymerize if the shelf life or storage temperature

are greatly exceeded. Heat develops during polymerization.

Disposal considerations

Incinerate in suitable incineration plant, observing local authority regulations.

A waste code in accordance with the European waste catalog (EWC) cannot be specified, due to

dependence on the usage.

The waste code in accordance with the European waste catalog (EWC) must be specified in

cooperation with disposal agency/manufacturer/authorities.

Contaminated packaging:

Contaminated packaging should be emptied as far as possible; then it can be passed on for recycling

after being thoroughly cleaned.