Registration Dossier

Administrative data

First-aid measures

Description of first aid measures
Remove contaminated clothing.
On skin contact:
Wash thoroughly with soap and water. Areas affected by molten material should be quickly placed
under cold running water. Burns caused by molten material require hospital treatment.
On contact with eyes:
Immediately wash affected eyes for at least 15 minutes under running water with eyelids held open,
consult an eye specialist.
On ingestion:
Rinse mouth and then drink plenty of water.
Indication of any immediate medical attention and special treatment needed
Treatment: Treat according to symptoms (decontamination, vital functions), no known specific
antidote.

Fire-fighting measures

Extinguishing media
Suitable extinguishing media:
water spray, dry powder, carbon dioxide, alcohol-resistant foam
Unsuitable extinguishing media for safety reasons:
Dry Powder for Class D
Special hazards arising from the substance or mixture
nitrogen oxides, carbon oxides
The substances/groups of substances mentioned can be released in case of fire. Under certain
conditions in case of fire other hazardous combustion products may be generated.
Advice for fire-fighters
Special protective equipment:
Wear a self-contained breathing apparatus.
Further information:
Collect contaminated extinguishing water separately, do not allow to reach sewage or effluent
systems.

Accidental release measures

Personal precautions, protective equipment and emergency procedures
Avoid contact with the skin, eyes and clothing.
Environmental precautions
Discharge into the environment must be avoided.
Methods and material for containment and cleaning up
For small amounts: Allow to solidify and sweep/shovel up. Dispose of absorbed material in
accordance with regulations.
For large amounts: Allow to solidify and sweep/shovel up. Dispose of absorbed material in
accordance with regulations.

Handling and storage

Precautions for safe handling
Ensure thorough ventilation of stores and work areas.
Conditions for safe storage, including any incompatibilities
Suitable materials for containers: Low density polyethylene (LDPE), glass, High density polyethylene
(HDPE), aluminum, Stove-lacquer RDL 16
Further information on storage conditions: Containers should be stored tightly sealed in a dry place.
Protect against moisture.
Storage stability:
Storage temperature: 65 °C
Storage duration: 24 Months
From the data on storage duration in this safety data sheet no agreed statement regarding the
warrantee of application properties can be deduced.
Protect from temperatures below: 50 °C
The product crystallizes below the limit temperature.
Protect from temperatures above: 70 °C
To protect product purity, maintain indicated storage temperature.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Control parameters
Components with workplace control parameters
126-30-7: 2,2-Dimethylpropane-1,3-diol
PNEC
freshwater: 0.5 mg/l
marine water: 0.05 mg/l
intermittent release: 5 mg/l
sediment (freshwater): 1.3 mg/kg
sediment (marine water): 0.13 mg/kg
soil: 0.166 mg/kg
STP: 10 mg/l
DNEL
worker:
Long-term exposure- systemic effects, dermal: 5 mg/kg
worker:
Long-term exposure- systemic effects, Inhalation: 8.7 mg/m3
consumer:
Long-term exposure- systemic effects, dermal: 2.5 mg/kg
consumer:
Long-term exposure- systemic effects, Inhalation: 2.9 mg/m3
Exposure controls
Personal protective equipment
Respiratory protection:
Wear respiratory protection if ventilation is inadequate. Consider the risk management measures as
outlined in the exposure scenario.
Hand protection:
Chemical resistant protective gloves (EN 374)
Suitable materials short-term contact and/or splashes (recommended: At least protective index 2,
corresponding > 30 minutes of permeation time according to EN 374)
butyl rubber (butyl) - 0.7 mm coating thickness
Use additional heat protection gloves when handling hot molten masses (EN 407), e.g. of textile or
leather.
Manufacturer's directions for use should be observed because of great diversity of types.
Supplementary note: The specifications are based on tests, literature data and information of glove
manufacturers or are derived from similar substances by analogy. Due to many conditions (e.g.
temperature) it must be considered, that the practical usage of a chemical-protective glove in
practice may be much shorter than the permeation time determined through testing.
Consider the risk management measures as outlined in the exposure scenario.
Eye protection:
Tightly fitting safety goggles (splash goggles) (e.g. EN 166), Consider the risk
management measures as outlined in the exposure scenario.
General safety and hygiene measures
Avoid contact with the skin, eyes and clothing. Wearing of closed work clothing is required
additionally to the stated personal protection equipment. Handle in accordance with good industrial
hygiene and safety practice.

Stability and reactivity

Reactivity
No hazardous reactions if stored and handled as prescribed/indicated.
Corrosion to metals: The product is not to be labelled as corrosive for transport purposes.
Formation of
flammable gases:
Remarks: Forms no flammable gases in the
presence of water.
Chemical stability
The product is stable if stored and handled as prescribed/indicated.
Possibility of hazardous reactions
No hazardous reactions known.
Conditions to avoid
Avoid humidity.
Incompatible materials
Substances to avoid:
atmospheric moisture
Hazardous decomposition products
No hazardous decomposition products if stored and handled as prescribed/indicated.

Disposal considerations

Waste treatment methods
Incinerate in suitable incineration plant, observing local authority regulations.
A waste code in accordance with the European waste catalog (EWC) cannot be specified, due to
dependence on the usage.
The waste code in accordance with the European waste catalog (EWC) must be specified in
cooperation with disposal agency/manufacturer/authorities.
Contaminated packaging:
Contaminated packaging should be emptied as far as possible; then it can be passed on for
recycling after being thoroughly cleaned.