Registration Dossier
Registration Dossier
Data platform availability banner - registered substances factsheets
Please be aware that this old REACH registration data factsheet is no longer maintained; it remains frozen as of 19th May 2023.
The new ECHA CHEM database has been released by ECHA, and it now contains all REACH registration data. There are more details on the transition of ECHA's published data to ECHA CHEM here.
Diss Factsheets
Use of this information is subject to copyright laws and may require the permission of the owner of the information, as described in the ECHA Legal Notice.
EC number: - | CAS number: -
- Life Cycle description
- Uses advised against
- Endpoint summary
- Appearance / physical state / colour
- Melting point / freezing point
- Boiling point
- Density
- Particle size distribution (Granulometry)
- Vapour pressure
- Partition coefficient
- Water solubility
- Solubility in organic solvents / fat solubility
- Surface tension
- Flash point
- Auto flammability
- Flammability
- Explosiveness
- Oxidising properties
- Oxidation reduction potential
- Stability in organic solvents and identity of relevant degradation products
- Storage stability and reactivity towards container material
- Stability: thermal, sunlight, metals
- pH
- Dissociation constant
- Viscosity
- Additional physico-chemical information
- Additional physico-chemical properties of nanomaterials
- Nanomaterial agglomeration / aggregation
- Nanomaterial crystalline phase
- Nanomaterial crystallite and grain size
- Nanomaterial aspect ratio / shape
- Nanomaterial specific surface area
- Nanomaterial Zeta potential
- Nanomaterial surface chemistry
- Nanomaterial dustiness
- Nanomaterial porosity
- Nanomaterial pour density
- Nanomaterial photocatalytic activity
- Nanomaterial radical formation potential
- Nanomaterial catalytic activity
- Endpoint summary
- Stability
- Biodegradation
- Bioaccumulation
- Transport and distribution
- Environmental data
- Additional information on environmental fate and behaviour
- Ecotoxicological Summary
- Aquatic toxicity
- Endpoint summary
- Short-term toxicity to fish
- Long-term toxicity to fish
- Short-term toxicity to aquatic invertebrates
- Long-term toxicity to aquatic invertebrates
- Toxicity to aquatic algae and cyanobacteria
- Toxicity to aquatic plants other than algae
- Toxicity to microorganisms
- Endocrine disrupter testing in aquatic vertebrates – in vivo
- Toxicity to other aquatic organisms
- Sediment toxicity
- Terrestrial toxicity
- Biological effects monitoring
- Biotransformation and kinetics
- Additional ecotoxological information
- Toxicological Summary
- Toxicokinetics, metabolism and distribution
- Acute Toxicity
- Irritation / corrosion
- Sensitisation
- Repeated dose toxicity
- Genetic toxicity
- Carcinogenicity
- Toxicity to reproduction
- Specific investigations
- Exposure related observations in humans
- Toxic effects on livestock and pets
- Additional toxicological data
![](https://echa.europa.eu/o/diss-blank-theme/images/factsheets/A-REACH/factsheet/print_toxicological-information.png)
Skin irritation / corrosion
Administrative data
- Endpoint:
- skin irritation: in vitro / ex vivo
- Type of information:
- experimental study
- Adequacy of study:
- key study
- Study period:
- April 28 - June 16, 2016
- Reliability:
- 1 (reliable without restriction)
- Rationale for reliability incl. deficiencies:
- guideline study
Data source
Reference
- Reference Type:
- study report
- Title:
- Unnamed
- Year:
- 2 016
- Report date:
- 2016
Materials and methods
Test guideline
- Qualifier:
- according to guideline
- Guideline:
- OECD Guideline 439 (In Vitro Skin Irritation: Reconstructed Human Epidermis Test Method)
- Deviations:
- no
- GLP compliance:
- yes (incl. QA statement)
Test material
- Test material form:
- solid: particulate/powder
- Details on test material:
- Batch No.: 2016JAN-15kg
Expiry Date: 01 January 2020
Appearance: Blue-white powder
Storage: Room temperature (15-25°C)
Safety precautions: Routine safety precautions (lab coat, gloves, safety glasses, face mask) for unknown materials were applied to assure personnel health and safety.
Constituent 1
impurity 1
- Specific details on test material used for the study:
- Batch No.: 2016JAN-15kg
Expiry Date: 01 January 2020
Appearance: Blue-white powder
Storage: Room temperature (15-25°C)
In vitro test system
- Test system:
- human skin model
- Source species:
- human
- Cell type:
- non-transformed keratinocytes
- Justification for test system used:
- The EPISKIN model has been validated for irritation testing in an international trial. After a review of scientific reports and peer reviewed publications on the EPISKIN method, it showed evidence of being a reliable and relevant stand-alone test for predicting rabbit skin irritation, when the endpoint is evaluated by MTT reduction and for being used as a replacement for the Draize Skin Irritation test (OECD TG 404 and Method B.4 of Annex V to Directive 67/548/EEC) for the purposes of distinguishing between skin irritating and no- skin irritating test substances (STATEMENT OF VALIDITY OF IN-VITRO TESTS FOR SKIN IRRITATION; ECVAM; Institute for Health & Consumer Protection; Joint Research Centre; European Commission; Ispra; 27 April 2007).
- Details on test system:
- Disks of EPISKIN (three units) were treated with test item and incubated for 15 minutes at room temperature. Exposure of test material was terminated by rinsing with PBS 1x solution. Epidermis units were then incubated at 37°C for 42 hours in an incubator with 5% CO2. The viability of each disk was assessed by incubating the tissues for 3 hours with MTT solution at 37°C in 5% CO2 protected from light. The precipitated formazan was then extracted using acidified isopropanol and quantified spectrophotometrically. SDS (5% aq.) and 1×PBS treated (three units / positive and negative control) epidermis were used as positive and negative controls respectively. For each treated tissue viability was expressed as a percentage relative to negative control. The test item has an intrinsic colour (blue-white), therefore two additional test item treated tissues were used for the non-specific OD evaluation.
Quality control:
EpiSkinTMSM kits are manufactured according to defined quality assurance procedures (certified ISO 9001). All biological components of the epidermis and the kit culture medium have been tested for the presence of viruses, bacteria and mycoplasma. The quality of the final product is assessed by undertaking an MTT cell viability test and a cytotoxicity test with sodium dodecyl sulphate (SDS).
TEMPERATURE USED FOR TEST SYSTEM
- Temperature used during treatment / exposure: The plates with the treated epidermis units were incubated for the exposure time of 15 minutes (± 0.5 min) at room temperature.
- Temperature of post-treatment incubation: After rinsing the units were placed into the plate wells with fresh pre-warmed “maintenance medium” (2 mL/well) below them and then incubated for 42 hours (± 1h) at 37°C in an incubator with 5 % CO2, ≥95% humidified atmosphere.
REMOVAL OF TEST MATERIAL AND CONTROLS
- Number of washing steps: After the incubation time the EpiSkinTMSM units were removed and rinsed thoroughly with approximately 25 mL PBS 1x solution to remove all of the test material from the epidermal surface. The rest of the PBS was removed from the epidermal surface with suitable pipette tip linked to a vacuum source (care was taken to avoid the damage of epidermis). The viability of each disk was assessed by incubating the tissues for 3 hours with MTT solution at 37°C in 5% CO2 protected from light. The precipitated formazan was then extracted using acidified isopropanol and quantified spectrophotometrically.
Following the formazan extraction, 2×200 µL sample from each tube was placed into the wells of a 96-well plate (labelled appropriately) and read the Absorbance / Optical Density of the samples in a 96-well plate spectrophotometer at 570 nm using acidified isopropanol solution as the blank (6×200 µL). - Control samples:
- yes, concurrent negative control
- yes, concurrent positive control
- yes, concurrent MTT non-specific colour control
- Amount/concentration applied:
- TEST MATERIAL
The test item was applied in its original form, no formulation was required. Subsequently, 10 mg of the test item was applied evenly to the epidermal surface.
NEGATIVE AND POSITIVE CONTROL
A volume of 10 µL positive control (SDS 5 % aq.) or negative control (1x PBS) was applied on the skin surface. - Duration of treatment / exposure:
- The plates with the treated epidermis units were incubated for the exposure time of 15 minutes (± 0.5 min) at room temperature.
- Duration of post-treatment incubation (if applicable):
- After rinsing the units were placed into the plate wells with fresh pre-warmed “maintenance medium” (2 mL/well) below them and then incubated for 42 hours (± 1h) at 37°C in an incubator with 5 % CO2, ≥95% humidified atmosphere.
- Number of replicates:
- Three replicates were used for the test item and positive and negative controls respectively. Furthermore, two additional test item treated replicates were used for colour controls.
Results and discussion
In vitro
Results
- Irritation / corrosion parameter:
- % tissue viability
- Value:
- > 99 - < 100
- Negative controls validity:
- valid
- Positive controls validity:
- valid
- Remarks on result:
- no indication of irritation
Any other information on results incl. tables
Pre incubation:
The “maintenance medium” was pre-warmed to. The appropriate number of an assay plate wells were filled with the pre-warmed medium (2 mL per well). The epidermis units were placed with the media below them, in contact with the epidermis into each prepared well and then incubated overnight atin an incubator with 5 % CO2,≥95% humidified atmosphere.
Applicant's summary and conclusion
- Interpretation of results:
- GHS criteria not met
- Conclusions:
- The results obtained from this in vitro skin irritation test, using the EPISKIN model, indicated that the test item reveals no skin irritation potential under the utilised testing conditions. The test item Neodymium fluoride oxide, magnesium doped is considered to be non-irritant to skin and these results should not drive any GHS classification.
- Executive summary:
Disks of EPISKIN (three units) were treated with test item and incubated for 15 minutes at room temperature. Exposure of test material was terminated by rinsing with PBS 1x solution. Epidermis units were then incubated at 37°C for 42 hours in an incubator with 5% CO2. The viability of each disk was assessed by incubating the tissues for 3 hours with MTT solution atin 5% CO2 protected from light. The precipitated formazan was then extracted using acidified isopropanol and quantified spectrophotometrically.
The test item has an intrinsic colour (blue-white), therefore two additional test item treated tissues were used for the non-specific OD evaluation.
SDS (5% aq.) and 1×PBS treated (three units / positive and negative control) epidermis were used as positive and negative controls respectively. For each treated tissue viability was expressed as a percentage relative to negative control.
The test chemical is identified as potentially requiring classification and labelling according to UN GHS (Category 2 or Category 1), if the mean relative viability after 15 minutes exposure and 42 hours post incubation is less or equal (≤) to 50% of the negative control.
In this in vitro skin irritation test using the EPISKIN model, the test item Neodymium fluoride oxide, magnesium doped did not show significantly reduced cell viability in comparison to the negative control(mean value: 99 %). Allobtained test item viability results were above or equal to 50 % when compared to the viability values obtained from the negative control. The test item was considered to be non-irritant to skin.
Information on Registered Substances comes from registration dossiers which have been assigned a registration number. The assignment of a registration number does however not guarantee that the information in the dossier is correct or that the dossier is compliant with Regulation (EC) No 1907/2006 (the REACH Regulation). This information has not been reviewed or verified by the Agency or any other authority. The content is subject to change without prior notice.
Reproduction or further distribution of this information may be subject to copyright protection. Use of the information without obtaining the permission from the owner(s) of the respective information might violate the rights of the owner.
![ECHA](/o/diss-blank-theme/images/factsheets/A-REACH/factsheet/echa_logo.png)
Mimo że ECHA udostępnia wiele materiałów online w Twoim języku, część tej strony jest dostępna tylko w języku angielskim. Więcej o praktykach ECHA związanych z mwielojęzycznością.
Witamy na stronie internetowej ECHA. Strona ta nie jest w pełni obsługiwana przez Internet Explorer 7 (i wcześniejsze wersje). Prosimy o zainstalowanie nowszej wersji Internet Explorer.
Niniejsza strona używa plików cookies, aby zapewnić optymalne korzystanie z naszych stron internetowych.
Dodatkowe informacje: jak używamy plików cookies.