Registration Dossier

Administrative data

First-aid measures

General: Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves.
Description of first aid measures:
Inhalation - Move to fresh air. Call a physician if symptoms develop or persist.
Skin contact - Wash off with soap and water. Get medical attention if irritation develops and persists.
Eye contact - Rinse with water. Get medical attention if irritation develops and persists.
Ingestion - Rinse mouth. Get medical attention if symptoms occur.

Most important symptoms and effects, both acute and delayed: exposure may cause temporary irritation, redness or discomfort.

Indication of any immediate medical attention and special treatment needed: treat symptomatically.

Fire-fighting measures

General fire hazards: no unusual fire or explosion hazards noted.
Suitable extinguishing media: Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).
Unsuitable extinguishing media: Do not use water jet as an extinguisher, as this will spread the fire.
Special hazards arising from the substance or mixture: During fire, gases hazardous to health may be formed.

Advice for firefighters
Special protective equipment for firefighters: Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Special firefighting procedures: Use standard firefighting procedures and consider the hazards of other involved materials.

Accidental release measures

Personal precautions, protective equipment and emergency procedures
For non-emergency personnel: Keep unnecessary personnel away. For personal protection, see 'Exposure controls/personal protection'.
For emergency responders: Keep unnecessary personnel away. Use personal protection recommended in 'Exposure controls/personal protection'.

Environmental precautions: Avoid discharge into drains, water courses or onto the ground.
Methods and material for containment and cleaning up:
Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.
Never return spills to original containers for re-use. For waste disposal, see 'Disposal considerations'.

Handling and storage

Precautions for safe handling: observe good industrial hygiene practices
Conditions for safe storage, including any incompatibilities: Store in original tightly closed container. Store away from incompatible materials.
Specific end us(s): not available

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Control Parameters
Occupational exposure limits: no exposure limits noted for ingredient(s)
Biological limit values: no biological exposure limits noted for the ingredient(s)
Recommended monitoring procedures: follow standard monitoring procedures.
Derived no effect levels (DNELs): not available.
Predicted no effect levels (PNECs): not available

Exposure Controls
Appropriate engineering controls: Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.

Individual protection measures, such as personal protective equipment
General information: Personal protection equipment should be chosen according to the CEN standards and in discussion with the supplier of the personal protective equipment.
Eye/face protection: wear safety glasses with side shields (or goggles).
Skin/hand protection: wear appropriate chemical resistant gloves and wear suitable protective clothing
Respiratory protection: in case of insufficient ventilation, wear suitable respiratory equipment
Thermal hazards: wear appropriate thermal protective clothing, when necessary

Hygiene measures: Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants.

Environmental exposure controls: environmental manager must be informed of all major releases

Stability and reactivity

Reactivity: The product is stable and non-reactive under normal conditions of use, storage and transport.
Chemical stability: Material is stable under normal conditions.
Possibility of hazardous reactions: No dangerous reaction known under conditions of normal use.
Conditions to avoid: Contact with incompatible materials.
Incompatible materials: Strong oxidising agents.
Hazardous decomposition products: No hazardous decomposition products are known.

Disposal considerations

Residual Waste: Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions).
Contaminated Packaging: Since emptied containers may retain product residue, follow label warnings even after container is emptied. Empty containers should be taken to an approved waste handling site for recycling or disposal.
EU Waste code: The Waste code should be assigned in discussion between the user, the producer and the waste disposal company.
Disposal methods/information: Collect and reclaim or dispose in sealed containers at licensed waste disposal site.
Special precautions: Dispose in accordance with all applicable regulations.