Registration Dossier

Administrative data

First-aid measures

- Description of first aid measures: not specifically necessary. Observance of good industrial hygiene is recommended.
- Most important symptoms and effects, both acute and delayed: specific information on symptoms and effects caused by the product are unknown.
- Indication of any immediate medical attention and special treatment needed: information not available

Fire-fighting measures

- Extinguishing media:
SUITABLE EXTINGUISHING EQUIPMENT: the extinguishing equipment should be of the conventional kind: carbon dioxide, foam, powder and water spray.
UNSUITABLE EXTINGUISHING EQUIPMENT: none in particular.
- Special hazards arising from the substance or mixture:
HAZARDS CAUSED BY EXPOSURE IN THE EVENT OF FIRE: Do not breathe combustion products. The product is combustible and, when the powder is released into the air in sufficient concentrations
and in the presence of a source of ignition, it can create explosive mixtures with air. Fires may start or get worse by leakage of the solid product from the container, when it reaches high temperatures or through contact with sources of ignition.
- Advice for firefighters:
GENERAL INFORMATION: use jets of water to cool the containers to prevent product decomposition and the development of substances potentially hazardous for health. Always wear full fire prevention gear. Collect extinguishing water to prevent it from draining into the sewer system. Dispose of contaminated water used for extinction and the remains of the fire according to applicable regulations.
SPECIAL PROTECTIVE EQUIPMENT FOR FIRE-FIGHTERS: normal fire fighting clothing i.e. fire kit (BS EN 469), gloves (BS EN 659) and boots (HO specification A29 and A30) in combination with self-contained open circuit positive pressure compressed air breathing apparatus (BS EN 137).

Accidental release measures

- Personal precautions, protective equipment and emergency procedures: if there are no contraindications, spray powder with water to prevent the formation of dust. Wear suitable protective equipment (including personal protective equipment referred to under Section 8 of the safety data sheet) to prevent any contamination of skin, eyes and personal clothing. These indications apply for both processing staff and those involved in emergency procedures.
- Environmental precautions: the product must not penetrate into the sewer system or come into contact with surface water or ground water.
- Methods and material for containment and cleaning up: collect the leaked product and place it in containers for recovery or disposal. If the product is flammable, use explosion-proof equipment. If there are no contraindications, use jets of water to eliminate product residues. Make sure the leakage site is well aired. Evaluate the compatibility of the container to be used, by checking section Stability and reactivity. Contaminated material should be disposed of in compliance with the provisions set forth in Disposal considerations.
- Reference to other sections: any information on personal protection and disposal is given in sections Exposure controls/personal protection and Disposal considerations.

Handling and storage

- Precautions for safe handling: before handling the product, consult all the other sections of this material safety data sheet. Avoid leakage of the product into the environment. Do not eat, drink or smoke during use.
- Conditions for safe storage, including any incompatibilities: keep the product in clearly labelled containers. Keep containers away from any incompatible materials, see section Stability and reactivity for details.
- Specific end use(s): information not available.

Transport information

Land transport (ADR/RID)

UN number:
Not applicable.
Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (ADN(R))

UN number:
Not applicable.
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

UN number:
Not applicable.
Remarksopen allclose all

Air transport ICAO/IATA

UN number:
Not applicable.
Remarksopen allclose all

Additional transport information

Additional transport information
The product is not dangerous under current provisions of the Code of International Carriage of Dangerous Goods by Road (ADR) and by Rail (RID), of the International Maritime Dangerous Goods Code (IMDG), and of the International Air Transport Association (IATA) regulations.

Exposure controls / personal protection

- Control parameters: information not available
- Exposure controls: during the risk assessment process, it is essential to take into consideration the ACGIH occupational exposure levels for inert particulate not otherwise classified (PNOC respirable fraction: 3 mg/m3; PNOC inhalable fraction: 10 mg/m3). For values above these limits, use a P type filter, whose class (1, 2 or 3) must be chosen according to the outcome of risk assessment. As the use of adequate technical equipment must always take priority over personal protective equipment, make sure that the workplace is well aired through effective local aspiration. when choosing personal protective equipment, ask your chemical substance supplier for advice. Personal protective equipment must be CE marked, showing that it complies with applicable standards. Provide an emergency shower with face and eye wash station.
HAND PROTECTION:
In the case of prolonged contact with the product, protect the hands with penetration-resistant work gloves (see standard EN 374). Work glove material must be chosen according to the use process and the products that may form. Latex gloves may cause sensitivity reactions.
SKIN PROTECTION: wear category II professional long-sleeved overalls and safety footwear (see Directive 89/686/EEC and standard EN ISO 20344). Wash body with soap and water after removing protective clothing.
EYE PROTECTION: wear airtight protective goggles (see standard EN 166).
RESPIRATORY PROTECTION: use a type P filtering facemask, whose class (1, 2 or 3) and effective need, must be defined according to the outcome of risk assessment (see standard EN 149).
ENVIRONMENTAL EXPOSURE CONTROLS: the emissions generated by manufacturing processes, including those generated by ventilation equipment, should be checked to ensure compliance with environmental standards.

Stability and reactivity

- Reactivity: there are no particular risks of reaction with other substances in normal conditions of use.
- Chemical stability: the product is stable in normal conditions of use and storage.
- Possibility of hazardous reactions: the powders are potentially explosive when mixed with air.
- Conditions to avoid: avoid environmental dust build-up.
- Incompatible materials: information not available.
- Hazardous decomposition products: information not available.

Disposal considerations

- Waste treatment methods: reuse, when possible. Product residues should be considered special hazardous waste. The hazard level of waste containing this product
should be evaluated according to applicable regulations. Disposal must be performed through an authorised waste management firm, in compliance with national and local regulations.
CONTAMINATED PACKAGING: contaminated packaging must be recovered or disposed of in compliance with national waste management regulations.