Registration Dossier

Administrative data

First-aid measures

Description of first aid measures
· General information:
Symptoms of poisoning may even occur after several hours; therefore medical observation for at
least 48 hours after the accident.
Immediately remove any clothing soiled by the product.
Take affected persons out of danger area and lay down.
· After inhalation:
Supply fresh air and to be sure call for a doctor.
In case of unconsciousness place patient stably in side position for transportation.
· After skin contact: Immediately wash with water and soap and rinse thoroughly.
· After eye contact: Rinse opened eye for several minutes under running water.
· After swallowing: Call for a doctor immediately.
· Information for doctor:
· Most important symptoms and effects, both acute and delayed
No further relevant information available.
· Indication of any immediate medical attention and special treatment needed
No further relevant information available.

Fire-fighting measures

Extinguishing media
· Suitable extinguishing agents:
CO2, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
· For safety reasons unsuitable extinguishing agents: Water with full jet
· Special hazards arising from the substance or mixture
During heating or in case of fire poisonous gases are produced.
Sulphur dioxide (SO2)
· Advice for firefighters
· Protective equipment:
Wear self-contained respiratory protective device.
Do not inhale explosion gases or combustion gases.

Accidental release measures

Personal precautions, protective equipment and emergency procedures
Avoid formation of dust.
Wear protective clothing.
· Environmental precautions: Do not allow to enter sewers/ surface or ground water.
· Methods and material for containment and cleaning up:
Pick up mechanically.
Dispose contaminated material as waste according to item 13.
Ensure adequate ventilation.

Handling and storage

· Precautions for safe handling
Prevent formation of dust.
Ensure good ventilation/exhaustion at the workplace.
· Information about fire - and explosion protection:
Keep ignition sources away - Do not smoke.
Protect against electrostatic charges.
· Conditions for safe storage, including any incompatibilities
· Storage:
· Requirements to be met by storerooms and receptacles: Store only in the original receptacle.
· Information about storage in one common storage facility: Do not store together with acids.
· Further information about storage conditions:
Keep container tightly sealed.
Store in dry conditions.
· Specific end use(s) No further relevant information available.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (IMDG)

Remarksopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Additional information about design of technical facilities:
local ventilation
No further data; see item 7.
· Control parameters
· Ingredients with limit values that require monitoring at the workplace: Not required.
· Additional information: The lists valid during the making were used as basis.
· Exposure controls
· Personal protective equipment:
· General protective and hygienic measures:
The usual precautionary measures are to be adhered to when handling chemicals.
Keep away from foodstuffs, beverages and feed.
Wash hands before breaks and at the end of work.
Do not inhale dust / smoke / mist.
· Respiratory protection:
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer
exposure use self-contained respiratory protective device.
· Protection of hands:
Protective gloves
The glove material has to be impermeable and resistant to the product/ the substance/ the
Due to missing tests no recommendation to the glove material can be given for the product/ the
preparation/ the chemical mixture.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the
· Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks
of quality and varies from manufacturer to manufacturer.
· Penetration time of glove material
The exact break through time has to be found out by the manufacturer of the protective gloves and
has to be observed.
· Eye protection: Safety glasses

Stability and reactivity

· Chemical stability
· Thermal decomposition / conditions to be avoided:
No decomposition if used and stored according to specifications.
· Possibility of hazardous reactions
With strong oxidizing agents formation of sulphur dioxide
With concentrated acids formation of hydrogen sulphide
· Conditions to avoid No further relevant information available.
· Incompatible materials:
strong acids
strong oxidizing agents
· Hazardous decomposition products:
Sulphur dioxide
Hydrogen sulphide

Disposal considerations

Waste treatment methods
· Recommendation Disposal must be made according to official regulations
· European waste catalogue
06 06 03 wastes containing sulphides other than those mentioned in 06 06 02
· Uncleaned packaging:
· Recommendation: Disposal must be made according to official regulations.